Vidikron 60 manual Troubleshooting, Symptom Probable Cause Solution

Page 45

TROUBLESHOOTING

The following is a basic troubleshooting guide that can assist you in resolving typical problems may result in normal operation. If you have encountered problems that are not listed in this guide, please contact your Vidikron dealer for assistance.

Symptom

Probable Cause

Solution

Power is not supplied.

Is the power cord disconnected?

Insert the power cord (plug) firmly.

 

Is the light-source lamp cover closed correctly?

After the projector goes into the stand-by state

 

 

with the [STAND BY] indicator on, unplug from

 

 

the main power outlet, close the light-source lamp

 

 

cover correctly and plug in again.

 

Has the lamp life expired? (Has the lamp time

After the projector goes into the stand-by state with

 

reached 2000 hours?)

the [STAND BY] indicator on, un-plug from the

 

 

main power outlet, replace light-source lamp and

 

 

plug in again.

 

 

Reset the lamp time after replacing the lamp.

Light is not emitted, or

Is the lens cap removed?

Remove the lens cap.

light is dim.

 

 

 

Is the lamp near exhaustion?

Check the “Lamp time” on the menu, and if the

 

 

lamp is near exhaustion, prepare a new lamp and

 

 

install as soon as possible.

With power on, the

Is the air inlet or exhaust vent area blocked?

After the projector goes into the stand-by state

projector works but

 

with the [STAND BY] indicator on, un-plug from

stops abruptly in a few

 

the main power outlet, remove any blocking object

minutes.

 

and plug in again.

Video image does not

Is the correct input terminal selected?

Select the correct input with the [VIDEO] and

appear, or audio sound

 

[RGB] buttons.

does not occur.

 

 

 

 

 

 

Are devices connected correctly?

Connect devices correctly.

 

Are signals being supplied from the connected

Set connected devices correctly.

 

devices?

 

 

Are input signals (scanning frequency, etc.)

Check if the signal is appropriate (scanning

 

appropriate?

frequency, etc.) and input the appropriate signal.

Video image is fuzzy

Is the focus adjusted correctly?

Adjust focus with the focus ring of the lens.

 

Is the projector placed too near or too far from the

Set the projector at the correct distance.

 

screen?

 

Video image is

Is the “Brightness” adjusted correctly?

Adjust “Brightness” using the menu.

abnormally dark or

 

 

bright.

 

 

Color is poor or unstable.

Is the picture quality (color density, etc.) adjusted

Adjust picture quality using the menu.

 

correctly?

 

 

Are signals (scanning frequency, etc.) from the

Check if the signal is appropriate (scanning

 

connected device appropriate?

frequency, etc.), and input the appropriate signal.

 

Is the [RGB2] input terminal being used?

When the [RGB2] input terminal is being used,

 

 

“RGB2(BNC)” must be selected from the

 

 

“Projector Opt” menu. Set it correctly according

 

 

to the input signal.

44

Page 44 Page 46
Image 45
Page 44 Page 46
Contents L a P R O J E C T O R Table of Contents » Contents of the package » The features you’ll enjoy includeIntroduction » OptionsAbout the installation place Safety PrecautionsFCC Information U.S.A. only About burning-in of the D-ILA deviceSafety Precautions Power Connection Using the screen mode switch function Cleaning the lensViewing conditions Brightness of the room Do not view the screen continually for a long timeFor Projectors, Video Processors and Controllers Limited WarrantyEffective Warranty Date » Projector Chassis Cover Controls and FeaturesTo Open the Projector Cover To Close the Projector CoverLamp Button » Control Panel on the ProjectorInput Terminal » Connector PanelRGB1 DVI RGB3Audio » Remote Control Cursor OFFPC 4x3 Button PC 16x9 ButtonENT Enter Button VID S-Video Button» Installing the Projector against the Screen Installing the ProjectorThrow Distance Chart Screen Installation» Projection Distance and Screen Size 43 Screen» Signals that can be input into the projector Connecting to Various DevicesVideo Signals Response to Decoder Responds to double density*5, high-vision signalsAllowable input signals Hdcp compatible signal» Connecting to Devices Connecting to Video DevicesRight Side of Projector Connecting to Computers Control from External Device Connecting the Power Cord Supplied Basic Operation Basic Operation Mute Pause Keystone Auto ADJ » Frequently Used Convenient FunctionsUsing the Auto Adjust function for automatic adjustments Auto Adjust functionAdjustment and Settings Using Menus When video input is selected» Menu Structure » When RGB input is selected » When no image signal is inputted » Menu Operation Buttons » The Procedure for Menu Operation Press the Menu button » The Menu Configuration Adjustment and Settings Using Menus Adjustment and Settings Using Menus Setting Aspect Ratio and Resize » Setting the Aspect RatioProject the image onto the screen Press the Menu button Select Letterbox with the cursor buttons Press the Menu button to end when adjustment is completedSelect Resize with the cursor buttons / and press Enter » Setting the ResizeSelect Letterbox with the cursor buttons When lamp time exceeds 1000 hours Replacing the Lamp for Service onlyWhen the lamp time exceeds 2000 hours When the lamp time exceeds 2010 hoursResetting the Lamp Time for Service only Insert the power cord into the wall outletTo ensure the lamp hours have been reset Command Format Command Data Format Communication SpecificationsRS-232 External Control Response Data FormatRGB3 External Control Command TableSymptom Probable Cause Solution TroubleshootingSymptom Probable Cause Solution Message Cause Contents What to do When These Messages are Displayed» About Warning Indicators Dimensions Vision Model 60 Projector Specifications
Top Page Image Contents