AMD 7ZX-1 user manual FCC Compliance Statement, Declaration of Conformity

Page 2

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name: G.B.T. INC.

Address: 18305 Valley Blvd., Suite#A

LA Puent, CA 91744

Phone/Fax No: (818) 854-9338/ (818) 854-9339

hereby declares that the product

Product Name: Mother Board

Model Number: GA-7ZX

Conforms to the following specifications:

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a), Class B Digital Device

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1)

This device may not cause harmful

and

(2)

this device must accept any inference received, including

that may cause undesired operation.

 

Representative Person's Name:

ERIC LU

Signature:

Eric Lu

Date:

Jun. 30, 2000

FCC Compliance Statement:

This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Move the equipment away from the receiver

-Plug the equipment into an outlet on a circuit different from that to which the receiver is connected

-Consult the dealer or an experienced radio/television technician for additional suggestions

You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void Your authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation.

Image 2
Contents 7ZX-1 FCC Compliance Statement Declaration of ConformityDeclaration of Conformity Table Of Content Panel and Jumper DefinitionAppendix Acronyms Revision History Summary Of Features CPU7ZX-1 Motherboard Layout 7ZX-1Ë100 102 104 106 108 110 112 133 CPU Speed SetupË100 105 110 113 115 117 133 Game & Audio Port ConnectorsUSB 1 Connector COM a / COM B / LPT PortJ3 CPU Fan USB 2 ConnectorPS/2 Keyboard & PS/2 Mouse Connector J2 Sysem Fan JP6 Power FanATX Power Floppy Port IDE1Primary, IDE2Secondary PortJ12 Wake On LAN J13 Ring Power On Internal Modem Card Wake UpJ18 CD Audio Line JP8 / LED1 STR LED Connector & Dimm LED J4 IRJP16 /JP17/JP18 AMR Primary or Secondary Select Optional J11 2x11 Pins JumperPanel And Jumper Definition GN HDJP9 Onboard Sound Function Selection Optional JP4 Rear USB Device Wake up Selection USB Connector USB1JP7 STR Function Enabled Suspend To RAM JP3 Clear Cmos Function Optional JP10 Bios Write Protection OptionalJP11 Front USB Device Wake up Selection USB Port USB2 USB2BAT1 Battery Winstone99 Performance ListWinbench99 Block Diagram VT82CHow to put your system into STR mode? Suspend To RAM InstallationSTR function Installation Introduce STR functionSuspend to RAM Installation How to recover from the STR sleep mode? Memory Installation Main Menu Bios SetupStatus Page Setup Menu / Option Page Setup Menu Main Menu Standard Cmos Setup Memory Boot Sector Virus ProtectionFloppy Drive a / Drive B Base MemoryBios Features Setup Chipset Features Setup Sdram Command Drive Bios Flash ProtectionDelay Dram Read Latch USB ControllerPower Management Setup Modem USE IRQ Resume On RTC AlarmSystem after AC Back Function Resume On Ring / LANPnP/PCI Configurations Load Bios Defaults Load Bios Defaults Y/N? NLoad Setup Defaults Load Setup DefaultsIntegrated Peripherals Parallel Port IRQ Parallel Port ModeParallel Port DMA AC97 AudioGame Port 200h-207h MPU-401MPU-401 I/O Address Hardware Monitor Set Supervisor / User Password PNP/PCI CONFIGURATIONEnter new supervisor passwordIDE HDD Auto Detection Save & Exit Setup Save to Cmos and EXITY/N? YExit Without Saving Quit without saving Y/N ? NAppendix Acronyms