AMD 7ZX-1 user manual JP4 Rear USB Device Wake up Selection USB Connector USB1

Page 17

Panel and Jumper Definition

JP4: Rear USB Device Wake up Selection (USB Connector USB1)

USB1

	1
	1


Pin No.						Definition
1-2 Close	Normal (Default)
2-3 Close	USB Device Wake up

(If you want to use "USB Dev Wakeup From S3-S5" function, you have to set the BIOS setting "USB Dev Wakeup From S3-S5" enabled, and the jumper "JP4" enabled).

*(Power on the computer and as soon as memory counting starts, press <Del>. You will enter BIOS Setup. Select the item "POWER MANAGEMENT SETUP", then select "USB Dev Wakeup From S3-S5: Enabled". Remember to save the setting by pressing "ESC" and choose the "SAVE & EXIT SETUP" option.)

JP7: STR Function Enabled (Suspend To RAM)

	1


Pin No.			Definition
Open	Normal (Default)
Close		STR Enabled

JP9: Onboard Sound Function Selection (Optional)

JP9

1





Pin No.						Definition
1-2 close				Onboard Sound
				Enable (Default)
2-3 close				Onboard Sound
				Disable

12

Image 17

Contents 7ZX-1 Declaration of Conformity FCC Compliance StatementDeclaration of Conformity Panel and Jumper Definition Table Of ContentAppendix Acronyms Revision History CPU Summary Of Features7ZX-1 7ZX-1 Motherboard LayoutË100 102 104 106 108 110 112 133 CPU Speed SetupË100 105 110 113 115 117 133 USB 1 Connector ConnectorsGame & Audio Port COM a / COM B / LPT PortJ3 CPU Fan USB 2 ConnectorPS/2 Keyboard & PS/2 Mouse Connector J2 Sysem Fan JP6 Power FanATX Power IDE1Primary, IDE2Secondary Port Floppy PortJ12 Wake On LAN J13 Ring Power On Internal Modem Card Wake UpJ18 CD Audio Line J4 IR JP8 / LED1 STR LED Connector & Dimm LEDPanel And Jumper Definition J11 2x11 Pins JumperJP16 /JP17/JP18 AMR Primary or Secondary Select Optional GN HDJP9 Onboard Sound Function Selection Optional JP4 Rear USB Device Wake up Selection USB Connector USB1JP7 STR Function Enabled Suspend To RAM JP11 Front USB Device Wake up Selection USB Port USB2 JP10 Bios Write Protection OptionalJP3 Clear Cmos Function Optional USB2BAT1 Battery Winstone99 Performance ListWinbench99 VT82C Block DiagramSTR function Installation Suspend To RAM InstallationHow to put your system into STR mode? Introduce STR functionSuspend to RAM Installation How to recover from the STR sleep mode? Memory Installation Main Menu Bios SetupStatus Page Setup Menu / Option Page Setup Menu Main Menu Standard Cmos Setup Floppy Drive a / Drive B Boot Sector Virus ProtectionMemory Base MemoryBios Features Setup Chipset Features Setup Delay Dram Read Latch Bios Flash ProtectionSdram Command Drive USB ControllerPower Management Setup System after AC Back Function Resume On RTC AlarmModem USE IRQ Resume On Ring / LANPnP/PCI Configurations Load Bios Defaults Y/N? N Load Bios DefaultsLoad Setup Defaults Load Setup DefaultsIntegrated Peripherals Parallel Port DMA Parallel Port ModeParallel Port IRQ AC97 AudioGame Port 200h-207h MPU-401MPU-401 I/O Address Hardware Monitor PNP/PCI CONFIGURATIONEnter new supervisor password Set Supervisor / User PasswordIDE HDD Auto Detection Save to Cmos and EXITY/N? Y Save & Exit SetupQuit without saving Y/N ? N Exit Without SavingAppendix Acronyms