AMD 7ZX-1 System after AC Back Function, Modem USE IRQ, Resume On Ring / LAN, PME Event Wake Up

Page 34

7ZX-1 Motherboard

•System after AC Back Function

Memory	This function depends on computer status. . (Default
	Value)
Soft-Off	Set System Soft-Off Status
Full-On	Set System Full-On Status.

•Modem USE IRQ

3, 4, (Default Value) 5, 7, N/A

•Resume On Ring / LAN

Disabled

Enabled

Disabled Resume On Ring / LAN.

Enabled Resume On Ring / LAN. (Default Value)

•PME Event Wake Up

Disabled

Enabled

Disabled PME Event Wake Up.

Enabled PME Event Wake Up. (Default Value)

•Resume On RTC Alarm

You can set “Resume On RTC Alarm” item to enabled and key in Data/time to power on system.

Disabled

Enabled

Disable this function. (Default Value)

Enable alarm function to POWER ON system.

If the “Resume On RTC Alarm” is Enabled.

RTC Alarm Date :

RTC Alarm Hour:

RTC Alarm Minute :

RTC Alarm Second :

Every Day, 1~31

0~23

0~59

0~59

29

Image 34

Contents 7ZX-1 FCC Compliance Statement Declaration of ConformityDeclaration of Conformity Table Of Content Panel and Jumper DefinitionAppendix Acronyms Revision History Summary Of Features CPU7ZX-1 Motherboard Layout 7ZX-1Ë100 105 110 113 115 117 133 CPU Speed SetupË100 102 104 106 108 110 112 133 Game & Audio Port ConnectorsUSB 1 Connector COM a / COM B / LPT PortPS/2 Keyboard & PS/2 Mouse Connector USB 2 ConnectorJ3 CPU Fan ATX Power JP6 Power FanJ2 Sysem Fan Floppy Port IDE1Primary, IDE2Secondary PortJ18 CD Audio Line J13 Ring Power On Internal Modem Card Wake UpJ12 Wake On LAN JP8 / LED1 STR LED Connector & Dimm LED J4 IRJP16 /JP17/JP18 AMR Primary or Secondary Select Optional J11 2x11 Pins JumperPanel And Jumper Definition GN HDJP7 STR Function Enabled Suspend To RAM JP4 Rear USB Device Wake up Selection USB Connector USB1JP9 Onboard Sound Function Selection Optional JP3 Clear Cmos Function Optional JP10 Bios Write Protection OptionalJP11 Front USB Device Wake up Selection USB Port USB2 USB2BAT1 Battery Winbench99 Performance ListWinstone99 Block Diagram VT82CHow to put your system into STR mode? Suspend To RAM InstallationSTR function Installation Introduce STR functionSuspend to RAM Installation How to recover from the STR sleep mode? Memory Installation Status Page Setup Menu / Option Page Setup Menu Bios SetupMain Menu Main Menu Standard Cmos Setup Memory Boot Sector Virus ProtectionFloppy Drive a / Drive B Base MemoryBios Features Setup Chipset Features Setup Sdram Command Drive Bios Flash ProtectionDelay Dram Read Latch USB ControllerPower Management Setup Modem USE IRQ Resume On RTC AlarmSystem after AC Back Function Resume On Ring / LANPnP/PCI Configurations Load Bios Defaults Load Bios Defaults Y/N? NLoad Setup Defaults Load Setup DefaultsIntegrated Peripherals Parallel Port IRQ Parallel Port ModeParallel Port DMA AC97 AudioMPU-401 I/O Address MPU-401Game Port 200h-207h Hardware Monitor Set Supervisor / User Password PNP/PCI CONFIGURATIONEnter new supervisor passwordIDE HDD Auto Detection Save & Exit Setup Save to Cmos and EXITY/N? YExit Without Saving Quit without saving Y/N ? NAppendix Acronyms