AMD 7ZX-1 USB Controller, USB Legacy Support, Bios Flash Protection, Dram Drive Strength

Page 32

7ZX-1 Motherboard

•USB Controller

Enabled	Enabled USB Controller. (Default Value)
Disabled	Disabled USB Controller.

•USB Legacy Support

Keyboard/FD

D

KB/Mouse/F

DD

Disabled

Set USB Legacy Support Keyboard / Floppy.

Set USB Legacy Support Keyboard / Mouse /Floppy.

Disabled USB Legacy Support Function. (Default

Value)

•BIOS Flash Protection

Enabled	BIOS Flash Write Protection.
Disabled	Normal. (Default Value)

•DRAM Drive Strength

Auto	Set DRAM Drive Strength Auto. (Default Value)
Manual	Set DRAM Drive Strength Manual.

If DRAM Drive Strength is Manual, then you can adjust item below.

•MD Bus Strength

High	Set MD Bus Strength High. (Default Value)
Low	Set MD Bus Strength Low.

•CAS Bus Strength

High	Set CAS Bus Strength High. (Default Value)
Low	Set CAS Bus Strength Low.

•Delay DRAM Read Latch

1.0ns		Set DRAM Read Latch Delay 1.0ns. (Default Value)
1.5ns		Set DRAM Read Latch Delay 1.5ns.
0.5ns		Set DRAM Read Latch Delay 0.5ns.
No delay		Set DRAM Read Latch No delay.
No delay		Set DRAM Read Latch No delay.

•Memory Data Drive

6 mA		Set Memory Data Drive 6 mA.
8 mA		Set Memory Data Drive 8 mA. (Default Value)

•SDRAM Command Drive

16 mA	Set SDRAM Command Drive 16 mA.
24 mA	Set SDRAM Command Drive 24 mA. (Default Value)

•Memory Address Drive

16 mA	Set Memory Address Drive 16 mA.
24 mA	Set Memory Address Drive 24 mA. (Default Value)

•CAS# Drive

8 mA	Set CAS# Drive 8 mA.
12 mA	Set CAS# Drive 12 mA. (Default Value)

•RAS# Drive

16 mA	Set RAS# Drive 16 mA.
24 mA	Set RAS# Drive 24 mA. (Default Value)

27

Image 32

Contents 7ZX-1 FCC Compliance Statement Declaration of ConformityDeclaration of Conformity Table Of Content Panel and Jumper DefinitionAppendix Acronyms Revision History Summary Of Features CPU7ZX-1 Motherboard Layout 7ZX-1Ë100 102 104 106 108 110 112 133 CPU Speed SetupË100 105 110 113 115 117 133 Connectors USB 1 ConnectorGame & Audio Port COM a / COM B / LPT PortJ3 CPU Fan USB 2 ConnectorPS/2 Keyboard & PS/2 Mouse Connector J2 Sysem Fan JP6 Power FanATX Power Floppy Port IDE1Primary, IDE2Secondary PortJ12 Wake On LAN J13 Ring Power On Internal Modem Card Wake UpJ18 CD Audio Line JP8 / LED1 STR LED Connector & Dimm LED J4 IRJ11 2x11 Pins Jumper Panel And Jumper DefinitionJP16 /JP17/JP18 AMR Primary or Secondary Select Optional GN HDJP9 Onboard Sound Function Selection Optional JP4 Rear USB Device Wake up Selection USB Connector USB1JP7 STR Function Enabled Suspend To RAM JP10 Bios Write Protection Optional JP11 Front USB Device Wake up Selection USB Port USB2JP3 Clear Cmos Function Optional USB2BAT1 Battery Winstone99 Performance ListWinbench99 Block Diagram VT82CSuspend To RAM Installation STR function InstallationHow to put your system into STR mode? Introduce STR functionSuspend to RAM Installation How to recover from the STR sleep mode? Memory Installation Main Menu Bios SetupStatus Page Setup Menu / Option Page Setup Menu Main Menu Standard Cmos Setup Boot Sector Virus Protection Floppy Drive a / Drive BMemory Base MemoryBios Features Setup Chipset Features Setup Bios Flash Protection Delay Dram Read LatchSdram Command Drive USB ControllerPower Management Setup Resume On RTC Alarm System after AC Back FunctionModem USE IRQ Resume On Ring / LANPnP/PCI Configurations Load Bios Defaults Load Bios Defaults Y/N? NLoad Setup Defaults Load Setup DefaultsIntegrated Peripherals Parallel Port Mode Parallel Port DMAParallel Port IRQ AC97 AudioGame Port 200h-207h MPU-401MPU-401 I/O Address Hardware Monitor Set Supervisor / User Password PNP/PCI CONFIGURATIONEnter new supervisor passwordIDE HDD Auto Detection Save & Exit Setup Save to Cmos and EXITY/N? YExit Without Saving Quit without saving Y/N ? NAppendix Acronyms