Analog Devices ADSP-21535 E-KIT LITE, 82-0000603-01 Completing Driver Installation Dialog Box

Page 25

Windows 2000 will automatically install the ADSP-21535 EZ-KIT Lite driver. The driver installation is now complete as shown in Figure 2-14.

Figure 2-14: Completing Driver Installation Dialog Box

8. Click Finish to exit the wizard.

Verify the installation by following the instructions in section 2.4.6.

2.4.6Verifying Driver Installation

Before you use the EZ-KIT Lite evaluation system, verify that the USB driver software is installed properly:

1.Ensure that the USB cable is connected to the evaluation board and the PC.

2.Verify that the yellow USB monitor LED (LED5) is lit. This signifies that the board is communicating properly with the host PC and is ready to run VisualDSP++.

ADSP-21535 EZ-KIT Lite Evaluation System Manual	2-14

Image 25

Contents ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Figures List of TablesAnalog Devices ADSP-21535 DSP IntroductionFor More Information About Analog Devices Products SdramPurpose of This Manual For Technical or Customer SupportIntended Audience Online Help Manual ContentsADSP-21535 Sharc DSP Document Name DescriptionGetting Started Contents of your EZ-KIT Lite PackageOverview Installation Tasks PC ConfigurationInstalling the VisualDSP++ License Installing the VisualDSP++ SoftwareInstalling the EZ-KIT Lite Debug Software EZ-KIT Lite Hardware Setup Setting Up the EZ-KIT Lite HardwareWindows 98 USB Driver Installation Installing the EZ-KIT Lite USB DriverSearch for the driver Driver is located Open the .sys File Finish the Software Installation 10 Found New Hardware Wizard Windows 2000 USB Driver Installation11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results Verifying Driver Installation 14 Completing Driver Installation Dialog BoxClick on New Session Starting VisualDSP++Using the Programmable Flag Pins Section Using the EZ-KIT LiteEZ-KIT Lite License Restrictions Start Address End Address ContentMemory Map Using Flash Memory Using the Sdram InterfaceRegister Value Function 0x2001 00FF 0x200A 0x2002 0x2000Flag Connected Use Using the Programmable Flag PinsUsing the Flash Programmer Utility Using the Power Management FeaturesPF14 PF13 PF12 Example ProgramsSystem Architecture Section EZ-KIT Lite Hardware ReferenceSystem Architecture DSPSPORT0 Audio Interface External Bus InterfaceExpansion Interface Connector InterfacesJtag Emulation Port Audio Input Select Jumper JP1 Jumper and DIP Switch SettingsAudio Codec Disable Jumper JP2 Stereo Linein DefaultBoot Mode Select Switch SW1 DSP PLL Setup Switch SW2Default PLL Setup Switch Settings SW2 DSP Pin Switch PositionLED and Push Button Locations LEDs and Push ButtonsReset LEDs LED7, LED8 Power LED LED6Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5Programmable Flag Push Buttons SW4, SW5, SW6, SW7 Reset Push Button SW8Push Button DSP Programmable Connector Locations ConnectorsPart Description Manufacturer Part Number Expansion Interface P1, P2, P3FlashLINK P4 Audio P5, P6Jtag P8 USB P7Specifications Power Connector P10SPORT0 P9 Terminal Connection Power SupplyBoard Current Measurements Resistor Voltage Plane DescriptionMechanical Drawing Mechanical DimensionsDescription Ref. Des Manufacturer Part Number Appendix a Bill of Materials3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps 4-5 IndexSPORT0