Analog Devices ADSP-21535 E-KIT LITE, 82-0000603-01 system manual Jumper and DIP Switch Settings

Page 37

4.3Jumper and DIP Switch Settings

This section describes the function of all the jumpers and DIP switches. The following figure shows the location of all the jumpers and DIP switches.

Figure 4-2: Jumper Locations

4.3.1Audio Input Select Jumper (JP1)

The audio input jack (P5) can be connected to the MIC1 or the LINEIN input channels of the AD1885 Codec (U7). When the JP1 jumpers connect pins 1 and 3 and pins 2 and 4, P3 connects to the mono MIC1 channel. When the jumpers connect pins 3 and 5 and pins 4 and 6, P5 connects to the stereo LINE_IN channel of the AD1885 Codec. These jumper settings are illustrated below in Figure 4-3.(The words MIC and LINE are on the board as a reference)

ADSP-21535 EZ-KIT Lite Evaluation System Manual	4-5

Image 37

Contents ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Figures List of TablesAnalog Devices ADSP-21535 DSP IntroductionFor More Information About Analog Devices Products SdramPurpose of This Manual For Technical or Customer SupportIntended Audience Online Help Manual ContentsADSP-21535 Sharc DSP Document Name DescriptionGetting Started Contents of your EZ-KIT Lite PackageOverview Installation Tasks PC ConfigurationInstalling the VisualDSP++ License Installing the VisualDSP++ SoftwareInstalling the EZ-KIT Lite Debug Software EZ-KIT Lite Hardware Setup Setting Up the EZ-KIT Lite HardwareWindows 98 USB Driver Installation Installing the EZ-KIT Lite USB DriverSearch for the driver Driver is located Open the .sys File Finish the Software Installation 10 Found New Hardware Wizard Windows 2000 USB Driver Installation11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results Verifying Driver Installation 14 Completing Driver Installation Dialog BoxClick on New Session Starting VisualDSP++Using the Programmable Flag Pins Section Using the EZ-KIT LiteEZ-KIT Lite License Restrictions Start Address End Address ContentMemory Map Using Flash Memory Using the Sdram InterfaceRegister Value Function 0x2001 00FF 0x200A 0x2002 0x2000Flag Connected Use Using the Programmable Flag PinsUsing the Flash Programmer Utility Using the Power Management FeaturesPF14 PF13 PF12 Example ProgramsSystem Architecture Section EZ-KIT Lite Hardware ReferenceSystem Architecture DSPSPORT0 Audio Interface External Bus InterfaceExpansion Interface Connector InterfacesJtag Emulation Port Audio Input Select Jumper JP1 Jumper and DIP Switch SettingsAudio Codec Disable Jumper JP2 Stereo Linein DefaultBoot Mode Select Switch SW1 DSP PLL Setup Switch SW2Default PLL Setup Switch Settings SW2 DSP Pin Switch PositionLED and Push Button Locations LEDs and Push ButtonsReset LEDs LED7, LED8 Power LED LED6Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5Programmable Flag Push Buttons SW4, SW5, SW6, SW7 Reset Push Button SW8Push Button DSP Programmable Connector Locations ConnectorsPart Description Manufacturer Part Number Expansion Interface P1, P2, P3FlashLINK P4 Audio P5, P6Jtag P8 USB P7Specifications Power Connector P10SPORT0 P9 Terminal Connection Power SupplyBoard Current Measurements Resistor Voltage Plane DescriptionMechanical Drawing Mechanical DimensionsDescription Ref. Des Manufacturer Part Number Appendix a Bill of Materials3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps 4-5 IndexSPORT0