Analog Devices ADSP-21535 E-KIT LITE, 82-0000603-01 system manual USB P7, Jtag P8

Page 45

4.5.4USB (P7)

The USB connector is a standard Type B USB receptacle. This connector is used to debug the DSP, and is not connected to the DSP’s USB interface.

Part Description		Manufacturer	Part Number
Type B USB receptacle (P7)		Mill-Max	897-30-004-90-000
		Digi-Key	ED90003-ND
	Mating Connector
USB cable (provided with kit)		Assmann	AK672-5
		Digi-Key	AK672-5ND

4.5.5JTAG (P8)

The JTAG header is the connecting point for a JTAG in-circuit emulator pod. When an emulator is connected to the JTAG header, the USB debug interface is disabled.

!NOTE: Pin 3 is missing to provide keying. Pin 3 in the mating connector should have a plug.

!NOTE: When using an emulator with the EZ-KIT Lite board, follow the connection instructions provided with the emulator.

ADSP-21535 EZ-KIT Lite Evaluation System Manual	4-13

Image 45

Contents ADSP-21535 EZ-KIT LITE Limited Warranty Regulatory Compliance Table of Contents Index List of Figures List of TablesAnalog Devices ADSP-21535 DSP IntroductionFor More Information About Analog Devices Products SdramFor Technical or Customer Support Purpose of This ManualIntended Audience Online Help Manual ContentsADSP-21535 Sharc DSP Document Name DescriptionContents of your EZ-KIT Lite Package Getting StartedOverview Installation Tasks PC ConfigurationInstalling the VisualDSP++ Software Installing the VisualDSP++ LicenseInstalling the EZ-KIT Lite Debug Software EZ-KIT Lite Hardware Setup Setting Up the EZ-KIT Lite HardwareWindows 98 USB Driver Installation Installing the EZ-KIT Lite USB DriverSearch for the driver Driver is located Open the .sys File Finish the Software Installation 10 Found New Hardware Wizard Windows 2000 USB Driver Installation11 Search for a Suitable Driver 12 Locate Driver Files 13 Driver File Search Results Verifying Driver Installation 14 Completing Driver Installation Dialog BoxClick on New Session Starting VisualDSP++Using the Programmable Flag Pins Section Using the EZ-KIT LiteStart Address End Address Content EZ-KIT Lite License RestrictionsMemory Map Using the Sdram Interface Using Flash MemoryRegister Value Function 0x2001 00FF 0x200A 0x2002 0x2000Flag Connected Use Using the Programmable Flag PinsUsing the Flash Programmer Utility Using the Power Management FeaturesPF14 PF13 PF12 Example ProgramsSystem Architecture Section EZ-KIT Lite Hardware ReferenceSystem Architecture DSPSPORT0 Audio Interface External Bus InterfaceConnector Interfaces Expansion InterfaceJtag Emulation Port Audio Input Select Jumper JP1 Jumper and DIP Switch SettingsAudio Codec Disable Jumper JP2 Stereo Linein DefaultBoot Mode Select Switch SW1 DSP PLL Setup Switch SW2Default PLL Setup Switch Settings SW2 DSP Pin Switch PositionLED and Push Button Locations LEDs and Push ButtonsReset LEDs LED7, LED8 Power LED LED6Programmable Flag LEDs LED1, LED2, LED3, LED4 USB Monitor LED LED5Reset Push Button SW8 Programmable Flag Push Buttons SW4, SW5, SW6, SW7Push Button DSP Programmable Connector Locations ConnectorsPart Description Manufacturer Part Number Expansion Interface P1, P2, P3FlashLINK P4 Audio P5, P6Jtag P8 USB P7Power Connector P10 SpecificationsSPORT0 P9 Terminal Connection Power SupplyBoard Current Measurements Resistor Voltage Plane DescriptionMechanical Drawing Mechanical DimensionsDescription Ref. Des Manufacturer Part Number Appendix a Bill of Materials3V-1.0AMP Regulator CT1 DIG01 PCT3226CT-ND Tant Panasonic ECJ-2VC1H390J NPO Appendix B Schematic ADSP-21535 EZ-KIT Lite For RTC ADSP-21535 EZ-KIT Lite DSP Memory ADSP-21535 EZ-KIT Lite Audio Codec ADSP-21535 EZ-KIT Lite Config Analog ADSP-21535 EZ-KIT Lite Connectors ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Power ADSP-21535 EZ-KIT Lite Bypass Caps 4-5 IndexSPORT0