AMX NXC-ME260 Replacing the Lithium Batteries, Battery CR2032 type 20mm coin cell Socket

Page 18

Installation and Wiring

To install a Master Card in either an NXF CardFrame or NXI Integrated Controller:

1.Discharge the static electricity from your body by touching a grounded object.

2.Unplug all the connectors from the Controller or Module.

3.Remove the two screws that hold the front plate on the Master Card, and remove the front plate.

4.Align the edges of the card with the guide slots inside the Master Card slot on the NXF or NXI.

5.Slide the card about halfway into the slot.

6.Inside the Master Card slot on the NXF or NXI, find the 6-pin control cable connector.

7.Plug the connector from the NXF or NXI into the 6-pin terminal on the Master Card. This connector is keyed to ensure correct orientation.

8.Once the control cable is connected, gently slide the card all the way in until you feel the rear edge of the card lightly snap into place.

9.Re-apply power and other connections as necessary.

Replacing the Lithium Batteries

The NXC-ME260 is equipped with two lithium batteries (FG# 57-0013) that have a life of approximately 5 years to protect their memory. When DC power is on, the batteries are not used. When replacing the batteries, remove one at a time to avoid losing the program in memory.

Battery (CR2032 type - 20mm coin cell)

socket

FIG. 10 Lithium battery and socket

1.Discharge the static electricity from your body by touching a grounded metal object.

2.Unplug all the connectors from the Controller or Module.

!NetLinx Integrated Controller (NXI): Remove the rear panel from the NXI. Then, disconnect the NXI control cable and remove the Master Card.

!NetLinx Module (NXM-xxx): Remove the rear panel from the Module, and remove the Master Card.

3.Carefully slide one battery out of its socket, and insert the new battery.

4.Plug the 2-pin PWR (green) connector to reapply power. Wait approximately 1 minute. Then, remove the PWR connector again.

5.Carefully slide the other battery out of its socket and insert the new battery.

6.Replace the Master Card (re-connect the NXI control cable to the Master Card if replacing in an NXI).

7.Replace the rear panel and secure with the mounting screws; reconnect all control, communication, and power cables.

 

14

NXC-ME260 NetLinx Master-Ethernet Card/Module

 

 

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents NXC-ME260 AMX Limited Warranty and Disclaimer Table of Contents Main Security Menu Default Security Configuration Product Information Front and rear panel componentsInput LED yellow Output LED red Status LED green Specifications NXM-ME260 SpecificationsEthernet ports used by the ME260 Ethernet Ports Used by the ME260Modes and front panel LED blink patterns Modes and LED Blink PatternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs Ethernet Layout of Ethernet LEDsProduct Information Baud rate settings Installation and WiringSetting the Program Port DIP Switch Program Run Disable PRD modePreparing/connecting captive wires Program Port Connections/WiringSetting the Program Port DIP switch DB-9 Program Port, Pinouts, and SignalsPin Program Port Pinouts and Signals ICSNet RJ-45 Connections/WiringICSHub RJ-45 Connections/Wiring ICSNet RJ-45 Pinouts/SignalsEthernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub in portICSHub OUT port SPE Port Connection/Wiring RJ-45 Plug RJ-45 wiring diagramExpansion in port RJ-11 TX enable No connect SPE Connector Pinouts and SignalsExpansion OUT connector on rear of NXC-ME260 SPE cable pinout informationMounting the NXC-ME260 in an NXF CardFrame or NXI RJ-11 Plug RJ-11 wiring diagramMounting the Modules Into an Equipment Rack Master Card slot on NXF CardFrame rear panelBattery CR2032 type 20mm coin cell Socket Replacing the Lithium BatteriesProgram Port Commands Program Port CommandsPC COM Port Communication Settings ProgrammingSET Time SET DateTime Device Status DPSDisk Free GET IP DPSMEM Ping IP Address Reboot DPSPass DPS Program InfoDirectnormal Route ModeSendcommand DPS Sendstring DPSShow Device DPS SET URL DPSShow Combine Displays a list of any combined devices ExampleShow LOG Show NotifyShow Remote Show RouteShow System TCP List ESC Pass CodesESC Pass Codes URL List DPSWindows client programs Linux Telnet clientFirmware Transfers Sending Firmware to a NetLinx Device KIT fileFirmware Transfers Security Terms Used in This Document NetLinx Security FeaturesNetLinx Security UserUser Name PasswordAccess Rights Group NameGetting connected Initial Setup via Telnet or Terminal ConnectionAccessing the Security configuration options ContMaster must be rebooted after changing the Http setting Security Options Menu Display system security options for NetLinx MasterAdd user Edit UserEdit User Menu Access Rights Menu Edit User MenuShow the list of authorized users Access Rights MenuDelete user Add GroupEdit Group Menu Add directory association Enables access to the user directory and all filesEdit Group Menu Subdirectories in the user directoryEdit Group menu Change Access Rights Edit Group menu Delete directory associationEdit Group menu List directory associations Edit Group menu Display Access Rights Edit GroupDelete Group Show List of Authorized Groups Set Telnet Timeout in secondsDisplay Telnet Timeout in seconds Make changes permanent by saving to flashMain Security Menu Main Security MenuDefault Security Configuration Help menu Help Menu OptionsLogging Into a Session Setup Security LogoutHelp Security AMX reserves
Related manuals
Manual 106 pages 58.54 Kb

NXC-ME260 specifications

The AMX NXC-ME260 is a cutting-edge piece of machinery designed to meet the demands of modern industrial environments. This equipment stands out due to its superior performance, enhanced efficiency, and innovative technologies, making it suitable for a wide range of applications.

One of the primary features of the NXC-ME260 is its robust design. Built with high-quality materials, this machine is engineered to withstand rigorous operating conditions, ensuring durability and longevity. The compact structure allows it to fit seamlessly into various workspaces, making it an ideal choice for operations with limited space.

Equipped with a powerful motor, the NXC-ME260 delivers exceptional speed and torque. This enables it to handle demanding tasks with ease, resulting in increased productivity. The machine’s advanced control system ensures precise operation, making it user-friendly and efficient. Its intuitive interface allows operators to quickly adapt to its functionalities, minimizing training time and boosting operational efficiency.

The NXC-ME260 integrates state-of-the-art technologies that enhance its performance. One of the standout features is its energy-efficient design, which reduces power consumption without compromising output. This makes the machine not only cost-effective but also an environmentally responsible choice for companies looking to reduce their carbon footprint.

Another significant technology incorporated in the NXC-ME260 is its intelligent monitoring system. This system provides real-time data on machine performance, allowing operators to make informed decisions and perform proactive maintenance. By predicting potential issues before they arise, the NXC-ME260 minimizes downtime and maintenance costs, ensuring uninterrupted operations.

Safety is paramount in any industrial setting, and the NXC-ME260 excels in this regard. It is equipped with multiple safety features, including emergency stop mechanisms and overload protection, ensuring operator safety and reducing the risk of accidents.

In summary, the AMX NXC-ME260 represents a convergence of power, efficiency, and safety-focused design. Its robust construction, advanced motor performance, intelligent monitoring system, and energy-efficient operation make it an invaluable asset for any industrial operation. Whether in manufacturing, logistics, or other sectors, the NXC-ME260 is engineered to enhance productivity while ensuring a safe working environment. Overall, this machine exemplifies the future of industrial equipment, bringing together technology and efficiency for optimal performance.
Top Page Image Contents