AMX NXC-ME260 Program Port Connections/Wiring, Setting the Program Port DIP switch

Page 12

Installation and Wiring

DIP Switch positions 2,3 and 4 must remain in the OFF position at all times.

Setting the Program Port DIP switch

1.Disconnect the power supply from the 2-pin PWR (green) connector on the Master Card.

2.Remove the front faceplate and four mounting screws from the Master Card's front panel. Then, locate the Program Port DIP switch (to the left of the Program port).

3.Set DIP switch positions according to the information listed in the Baud Rate Settings and PRD Mode Settings tables above.

4.Replace the front panel and faceplate back onto the Master Card and reconnect the 12 VDC power supply to the 2-pin PWR connector.

Program Port Connections/Wiring

Master Cards are equipped with two Program ports. One is located on the front panel and the other is on the rear for easy access. The port on the front panel is a DB-9 (male) connector, and the rear port is a 5-pin (male) connector. Use a Programming cable to connect the Program port to your PC's COM port to communicate with the Master Card. Then, you can download NetLinx programs to the Master Card with the NetLinx Studio software program. Refer to the NetLinx Studio instruction manual for programming instructions.

Preparing/connecting captive wires

1.Strip 0.25 inch of wire insulation off all wires.

2.Insert each wire into the appropriate opening on the connector according to the wiring diagrams and connector types described in this section. Do not tighten the screws excessively; doing so may strip the threads and damage the connector.

DB-9 Program port (front panel)

The following table shows the front panel DB-9 Program port connector, pinouts, and signals.

DB-9 Program Port, Pinouts, and Signals

DB-9 Program Port Connector

Pin

Signal

 

2

RX

 

3

TX

 

5

GND

7RTS

8CTS

 

8

NXC-ME260 NetLinx Master-Ethernet Card/Module

 

 

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents NXC-ME260 AMX Limited Warranty and Disclaimer Table of Contents Main Security Menu Default Security Configuration Product Information Front and rear panel componentsInput LED yellow Output LED red Status LED green Specifications NXM-ME260 SpecificationsEthernet ports used by the ME260 Ethernet Ports Used by the ME260Modes and front panel LED blink patterns Modes and LED Blink PatternsRear panel LEDs ICSNet/ICSHub Rear panel LEDs Ethernet Layout of Ethernet LEDsProduct Information Installation and Wiring Setting the Program Port DIP SwitchBaud rate settings Program Run Disable PRD modeProgram Port Connections/Wiring Setting the Program Port DIP switchPreparing/connecting captive wires DB-9 Program Port, Pinouts, and SignalsICSNet RJ-45 Connections/Wiring ICSHub RJ-45 Connections/WiringPin Program Port Pinouts and Signals ICSNet RJ-45 Pinouts/SignalsEthernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub in portICSHub OUT port SPE Port Connection/Wiring RJ-45 Plug RJ-45 wiring diagramExpansion in port RJ-11 SPE Connector Pinouts and Signals Expansion OUT connector on rear of NXC-ME260TX enable No connect SPE cable pinout informationRJ-11 Plug RJ-11 wiring diagram Mounting the Modules Into an Equipment RackMounting the NXC-ME260 in an NXF CardFrame or NXI Master Card slot on NXF CardFrame rear panelBattery CR2032 type 20mm coin cell Socket Replacing the Lithium BatteriesProgram Port Commands PC COM Port Communication SettingsProgram Port Commands ProgrammingSET Date TimeSET Time Device Status DPSDisk Free GET IP DPSMEM Reboot DPS Pass DPSPing IP Address Program InfoRoute Mode Sendcommand DPSDirectnormal Sendstring DPSSET URL DPS Show CombineShow Device DPS Displays a list of any combined devices ExampleShow LOG Show NotifyShow Remote Show RouteShow System ESC Pass Codes ESC Pass CodesTCP List URL List DPSWindows client programs Linux Telnet clientFirmware Transfers Sending Firmware to a NetLinx Device KIT fileFirmware Transfers NetLinx Security Features NetLinx SecuritySecurity Terms Used in This Document UserPassword Access RightsUser Name Group NameInitial Setup via Telnet or Terminal Connection Accessing the Security configuration optionsGetting connected ContMaster must be rebooted after changing the Http setting Security Options Menu Display system security options for NetLinx MasterAdd user Edit UserEdit User Menu Access Rights Menu Edit User MenuAccess Rights Menu Delete userShow the list of authorized users Add GroupEnables access to the user directory and all files Edit Group MenuEdit Group Menu Add directory association Subdirectories in the user directoryEdit Group menu Change Access Rights Edit Group menu Delete directory associationEdit Group menu List directory associations Edit Group menu Display Access Rights Edit GroupDelete Group Set Telnet Timeout in seconds Display Telnet Timeout in secondsShow List of Authorized Groups Make changes permanent by saving to flashMain Security Menu Main Security MenuDefault Security Configuration Help menu Help Menu OptionsLogging Into a Session Setup Security LogoutHelp Security AMX reserves
Related manuals
Manual 106 pages 58.54 Kb

NXC-ME260 specifications

The AMX NXC-ME260 is a cutting-edge piece of machinery designed to meet the demands of modern industrial environments. This equipment stands out due to its superior performance, enhanced efficiency, and innovative technologies, making it suitable for a wide range of applications.

One of the primary features of the NXC-ME260 is its robust design. Built with high-quality materials, this machine is engineered to withstand rigorous operating conditions, ensuring durability and longevity. The compact structure allows it to fit seamlessly into various workspaces, making it an ideal choice for operations with limited space.

Equipped with a powerful motor, the NXC-ME260 delivers exceptional speed and torque. This enables it to handle demanding tasks with ease, resulting in increased productivity. The machine’s advanced control system ensures precise operation, making it user-friendly and efficient. Its intuitive interface allows operators to quickly adapt to its functionalities, minimizing training time and boosting operational efficiency.

The NXC-ME260 integrates state-of-the-art technologies that enhance its performance. One of the standout features is its energy-efficient design, which reduces power consumption without compromising output. This makes the machine not only cost-effective but also an environmentally responsible choice for companies looking to reduce their carbon footprint.

Another significant technology incorporated in the NXC-ME260 is its intelligent monitoring system. This system provides real-time data on machine performance, allowing operators to make informed decisions and perform proactive maintenance. By predicting potential issues before they arise, the NXC-ME260 minimizes downtime and maintenance costs, ensuring uninterrupted operations.

Safety is paramount in any industrial setting, and the NXC-ME260 excels in this regard. It is equipped with multiple safety features, including emergency stop mechanisms and overload protection, ensuring operator safety and reducing the risk of accidents.

In summary, the AMX NXC-ME260 represents a convergence of power, efficiency, and safety-focused design. Its robust construction, advanced motor performance, intelligent monitoring system, and energy-efficient operation make it an invaluable asset for any industrial operation. Whether in manufacturing, logistics, or other sectors, the NXC-ME260 is engineered to enhance productivity while ensuring a safe working environment. Overall, this machine exemplifies the future of industrial equipment, bringing together technology and efficiency for optimal performance.
Top Page Image Contents