Agilent Technologies E1470A user manual Cascade Relays

Page 10

COM 00 010 002

011

001 012 000

COM 01

COM 02
030
022
031
021
032
020
COM 03
COM 04
050
042
051
041
052
040
COM 05

COM 10 110

102

111

101 112 100

COM 11

COM 12
130
122
131
121
132
120
COM 13

Channel Numbers are in the form bbc where

bb is the COM bank (00-05, 10-13, 20-25, or 30-33) c is the individual number (0, 1, or 2).

Channel		Cascade Relays
Numbers	K001	K002		K003
	K001	K002		K003
000					COM 00
					(3:1)
001
002
	K011	K012	K014	K013
010					COM 01
					(6:1)
011
012
	K021	K022	K024	K023
020					COM 02
					(9:1)
021
022
	K031	K032	K034	K033
030					COM 03
					(12:1)
031
032
	K041	K042	K044	K043
040					COM 04
					(15:1)
041
042
	K051	K052	K054
050				K056	K053
				18:1	COM 05
					COM 05
051				12:1	(30:1)
				12:1	(30:1)	A
052					Output	A
052					Output
			K055		to Right-Side
			K055		Board
	No Connection				Board
	No Connection
		12:1 Input
	K101	K102		K103
100					COM 10
					(3:1)
101
102
	K111	K112	K114	K113
110					COM 11
					(6:1)
111
112
	K121	K122	K124	K123
120					COM 12
					(9:1)
121
122
	K131	K132	K134	K133
130					COM 13
					(12:1)
131
132

Figure 1-2. Cascade RF Switch Switching Diagram (continued on next page)

10 Configuring the RF Switch

Chapter 1

Image 10

Contents E1470-90002 Page Contents Appendix C RF Switch Error Messages Index Agilent Technologies Warranty Statement Government Restricted RightsSafety Symbols Documentation HistoryDeclares, that the product Product Name Manufacturer’s NameManufacturer’s Address Model NumberPage Switching Diagram Using This ChapterChapter Cascade Relays COM 33 332 Configuring the RF Switch Chapter Creating Multiple MultiplexersChapter Configuring the RF Switch RF Switch ConfigurationMaximum POWER. The maximum RF power that can be applied On this moduleSetting the Logical Address Setting the Interrupt Request Level Connecting User Wiring Installing User Wiring Configuring the RF Switch ChapterAssembling SMB Connector Jacks SMB Connectors and Connector HousingsUser Connections Wiring Installing Device Drivers RF SwitchAddressing the Switch Programming the RF Switch ChapterChapter Programming the RF Switch Programming ExamplesProgramming the RF Switch Chapter Example Closing a Signal Path Example Opening Closing Signal Paths Example Saving Recalling Module States Programming the RF Switch Chapter Scpi Commands Format Command TypesCommon Commands Format Chapter RF Switch Command ReferenceLinking Commands Scpi Command ReferenceRF Switch Command Reference Chapter DIAGnostic DIAGnosticCLOSeDIAGnosticOPEN relay,relay... opens individual relays on DIAGnosticCLOSe?DIAGnosticOPEN Reset to its power-on state Common to NCDIAGnosticOPEN? DIAGOPEN333DIAGnosticRELAY? RSTDIAGThis programCLOS042,043,053,054,256REL?returnsROUTe ROUTePATHCOMMonExample Closing Channel Path 10002 SYSTem SYSTemERRor?SYSTemVERSion? Ieee 488.2 Common Commands Quick Reference CommandCommands Quick Reference DescriptionAppendix a RF Switch Specifications Appendix aRF Switch Specifications Appendix a Register Addressing Appendix BAbout This Appendix Addressing OverviewBase Address Figure B-1. Register Address Locations Within VXI A16A16 Address Space Outside the Command Module Table B-2. Register Map Register DefinitionsTable B-1. General Register-based Programming Method Register-Based Programming Appendix BTable B-3. Status Register Bit Patterns read Table B-4. Control Register Bit Pattern writeRelay Control Registers Vxie Table B-10. Writing to Relay Control Registers Register Programming Example Create and open a device sessionWait 5 seconds before resetting module Void errhandler /* Error Handling Routine Register-Based Programming Appendix B Appendix C RF Switch Error Messages Appendix CRF Switch Error Messages Appendix C Index IndexIndex E1470-90002