Allied Telesis C613-02013-00 manual Simple Switching, Command Line Interface

Page 11

Getting Started

11

Chapter 2

Getting Started

The Rapier switch is supplied with default settings which allow it to operate immediately as a switch, without any configuration. Even if this is all you want to use the switch for, you should still gain access to the switch configuration, if only to change the manager password to prevent unauthorised access.

To take advantage of the full range of advanced Layer 2 switching features, the switch configuration must be changed. Layer 3 routing capabilities may also require detailed configuration. The switch has both a Command Line Interface (CLI) and a Graphical User Interface (GUI) for configuration and management. Before you can use the GUI, you will need to login to the switch and use its CLI to allocate an IP address.

Simple Switching

If all you want the switch to do is switch traffic on your LAN, you need not perform any configuration. Simply power up the switch and connect devices to the switch ports. Switch learning is enabled by default, and all valid packets will be forwarded (“Layer 2 Switching Process” on page 43).

Command Line Interface

To use the command line interface (CLI) for configuring the switch, the first thing you need to do after physically installing the switch is to start a terminal session to access the switch (see Table 1 and the Rapier Switch Quick Install Guide).

To start a terminal session, do one of the following:

■Connect a VT100-compatible terminal to the RS-232 Terminal Port, set the communications parameters on the terminal (Table 1 on page 12), and press [Enter] a few times until the switch’s login prompt appears; or

■Connect the COM port of a PC running terminal emulation software such as Windows Terminal or HyperTerminal to the RS-232 Terminal Port, set the communications parameters on the terminal emulation software (Table 1 on page 12), and press [Enter] a few times until the switch’s login prompt appears.

Rapier Switch Software Release 2.2.1 C613-02013-00 Rev A

Page 10 Page 12
Image 11
Page 10 Page 12
Contents User Guide Page Contents Documentation Roadmap Chapter Why Read This User Guide?Technical support Where To Find More InformationSwitching Features What Can the Rapier Switch Do?Routing Features Advanced Feature Licence AT-RPFL3Upgrade Optional Features Command Line Interface Simple SwitchingLogging Giving the Switch an IP AddressEntering Commands SET PasswordEnabling the GUI Enable AT-RPFL3Upgrade Feature LicenceEnable GUI Starting the GUI Graphical User InterfaceNavigating Monitoring Show File User PrivilegesFile Subsystem Show System Online CLI HelpNone Configuration ScriptsSaving Configuration Entered with the GUI DramEditor Saving Configuration Entered with the CLIInstall Information Show Install Delete InstallReleases and Patches into the Switch Load METHOD=HTTP DESTINATION=FLASH Example Install Software Upgrade for Rapier SwitchShow Load Enable SnmpSnmp and MIBs Show Snmp Enable Snmp AuthenticatetrapEnabling and Disabling Switch Ports Switch PortsSTP EnabledISO8802-3 Csmacd OFFAcceptable Frames Types Autonegotiation of Port Speed and Duplex ModeSELECT=MACSRCMACDESTMACBOTHIPSRCIPDESTIPBOTH Port TrunkingShow VLAN=ALL Packet Storm Protection Port Mirroring Port security ADD Switch L3FILTER MatchEnable Switch Mirror Disable Switch Mirror INTRUSIONACTION=NONEDISCARDTRAPDISABLEVirtual LANs Example output from the Show Switch Port Intrusion commandRapier Switch User Guide Creating VLANs Without Vlan Tags Static and dynamic VLANsMarketing Vlan Switch Training Vlan Trunk ports GarpParameter Meaning Vlan TaggingFRAME=TAGGEDUNTAGGED Tagged VLANs Summary of Vlan Tagging RulesIngress Rules Layer 2 Switching ProcessGeneric Vlan Registration Protocol Gvrp Learning Process Disable Switch LearningShow Switch Enable Switch LearningEnable Switch Ageingtimer Disable Switch Ageingtimer SET Switch AGEINGTIMER=10..1000000Layer 2 Filtering Example output from the Show Switch Filter commandFRAME=UNTAGGEDTAGGED Egress RulesShow Switch QOS Quality of ServiceSET Switch QOS=P1,P2,P3,P4,P5,P6,P7,P8 Spanning Tree Port States Spanning Tree Protocol STPConfiguring STP SET STP=stpnameALL PRIORITY=0..65535 Example output from the Show STP command Parameters To display STP port information, use the command TCN Bpdu To show STP counters, use the commandINTERFACE=VLAN3 Interfaces to Layer 3 ProtocolsIgmp Snooping Purge STPShow IP Igmp Enable IP Igmp Disable IP IgmpSET IP Igmp TIMEOUT=1..65535 QUERYINTERVAL=1..65535 Group List TriggersEvent Page Show IP Interface Internet Protocol IPRouting Information Protocol RIP IP MulticastingUplink Novell IPXShow IPX Circuit Active Enable RsvpAppleTalk Resource Reservation Protocol RsvpRAW Show Rsvp Interface

C613-02013-00 specifications

The Allied Telesis C613-02013-00 is a versatile and powerful network switch designed to meet the demands of modern networking environments. This device is part of Allied Telesis's extensive range of networking solutions, catering to both enterprise and industrial applications. It is engineered for high performance, reliability, and ease of management, making it a suitable choice for organizations that require robust connectivity solutions.

One of the main features of the C613-02013-00 is its support for advanced Layer 2 switching capabilities. This provides businesses with the necessary tools to manage and direct network traffic efficiently. The switch includes support for VLAN (Virtual Local Area Network) technology, which allows for the segmentation of network traffic, enhancing both security and performance. With VLANs, organizations can isolate critical workloads and improve network management while ensuring that sensitive information is protected from unauthorized access.

Another key characteristic of the C613-02013-00 is its extensive support for Power over Ethernet (PoE). This feature enables the switch to deliver electrical power along with data over standard Ethernet cabling. This is particularly beneficial for powering devices such as IP cameras, wireless access points, and VoIP phones, reducing the need for additional power supply infrastructure. With PoE capabilities, the switch simplifies installation and enhances flexibility in deploying network devices.

The C613-02013-00 also boasts advanced network management features, including support for SNMP (Simple Network Management Protocol) for efficient monitoring and troubleshooting. This ensures that network administrators can maintain optimal performance and quickly address any issues that arise. Additionally, the switch supports network redundancy features like Rapid Spanning Tree Protocol (RSTP), which helps to prevent network loops and minimizes downtime.

In terms of physical characteristics, the C613-02013-00 is designed for durability and ease of deployment in various environments. Its compact form factor allows for effective space utilization in data centers and network closets. Moreover, it features a fanless design, making it suitable for deployment in noise-sensitive environments such as offices and classrooms.

In summary, the Allied Telesis C613-02013-00 is a robust network switch offering advanced features such as Layer 2 switching, PoE support, and comprehensive network management capabilities. Its design and performance make it an excellent choice for businesses seeking to enhance their network infrastructure with reliable and secure connectivity solutions.
Top Page Image Contents