Allied Telesis Patch 86261-04 manual PCR Module TTY, User Level, PCR Module IGMP, SWI Level

Page 11

Patch 86261-04 For Rapier and AT-8800 Series Switches

SHOW IGMPSNOOPING ROUTERADDRESS

11

PCR: 03726

Module: TTY, USER

Level: 3

The time recorded when a user logged in was overwritten when the same user logged in a second time while the original connection was still active. This meant the SHOW USER command displayed the same time for both connections. This issue has been resolved.

PCR: 03781

Module: STP

Level: 2

A buffer leak occurred when rapid STP was specified with the SET STP

MODE=RAPID command, but STP had not been enabled with the ENABLE

STP command. This issue has been resolved.

PCR: 03855

Module: IPG

Level: 2

Previously, an IP multicast stream destined for an IP multicast group was forwarded out ports in the All Groups IGMP snooping entry even after this entry had timed out. This issue has been resolved.

PCR: 03861

Module: IPV6

Level: 2

When a connector was plugged into one physical interface, the RIPng request packet was erroneously transmitted from all interfaces on the switch. This issue has been resolved.

PCR: 03873

Module: IPG

Level: 4

The STATIC and INTERFACE options have been removed from the PROTOCOL parameter in the ADD IP ROUTE FILTER and SET IP ROUTE FILTER commands. These parameters were redundant because received static and interface routes are always added to the route table.

PCR: 03890

Module: IGMP, SWI

Level: 2

The switch was adding a router port for multicast packets to destinations with an address in the range 224.0.0.x. Switch port entries are now only created for special router multicast addresses.

PCR: 03905

Module: TTY

Level: 3

A fatal error occurred in the text editor while selecting blocks and scrolling up. This issue has been resolved.

PCR: 03926

Module: PIM

Level: 2

Repeated Assert messages were sent after the prune limit expired. This issue has been resolved. The default dense mode prune hold time has been changed from 60 seconds to 210 seconds.

PCR: 03932

Module: PING

Level: 3

The ADD PING POLL command had a duplicate entry for the LENGTH parameter in the dynamic PING configuration if LENGTH was not the default value. This generated an incorrect configuration file when the CREATE CONFIG command was executed. This issue has been resolved.

PCR: 03935

Module: ISAKMP

Level: 3

ISAKMP debug messages now correctly output IPv6 addresses when using

IPv6, and IPv4 addresses when using IPv4.

Patch 86261-04 for Software Release 2.6.1 C613-10386-00 REV D

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Patch For Rapier and AT-8800 Series Switches PCR Module Ospf Level PCR Module IPG LevelPCR Module BRI PCR Module IPV6 LevelPCR 31098 Module Dhcp Level PCR Module Http LevelPCR Module SWI Level PCR Module FFS LevelPCR Module IPG ADD Igmpsnooping RouteraddressPCR Module Rstp Level Delete Igmpsnooping RouteraddressPCR 31152 Module Dhcp Level PCR Module Firewall LevelPCR 31147 Module Dhcp Level PCR Module PIM, PIM6 LevelPCR 31161 Module LOG Level PCR Module STP LevelPCR Module Core Level PCR 31159 Module FW, Vlan LevelPCR Module SW56 Level PCR Module PORTAUTH, USER,STP LevelPCR Module User Level PCR Module SW56, SWI Level PCR Module PORTAUTH, User LevelPCR 31192 Module LOG Level PCR Module BGP, IP LevelPCR 31237 Module Core Level PCR 31215 Module Snmp LevelPCR Module PIM Level PCR Module TTY, User LevelPCR Module IGMP, SWI Level PCR Module TTY LevelPCR Module BGP, IPG Level PCR Module Ipsec LevelPCR Module PKI Level PCR 31015 Module STPLevel PCR 03996 Module FIREWALLLevelPCR 31001 Module DHCPLevel PCR 31013 Module SWILevelCurrent Temperature Normal Fan Status Error requiring attention. Failed means there was an PCR Module Ldap Level PCR Module NTP LevelPCR Module PPP Level PCR 31122 Module Rmon Level PCR Module File LevelPCR 31102 Module Dhcp Level PCR 31106 Module MLD LevelPCR Module BGP Level PCR Module OSPF, IPG LevelPCR Module Ikmp Level PCR 03885 Module Core Level PCR Module ETH Level PCR Module Switch LevelPCR Module DHCP, Telnet Level PCR 03895 Module Dhcp LevelPCR Module DHCP6 Level PCR Module SCC LevelPCR 03914 Module IPG, Vlan Level PCR Module CORE, SW56 LevelPCR Module Ipsec Level PCR 03979 Module Core Level AvailabilityShow Igmpsnooping Routeraddress

Patch 86261-04 specifications

Allied Telesis Patch 86261-04 is a highly reliable and efficient network switch designed for both enterprise and small to medium-sized business environments. Renowned for its robust performance and advanced features, this patch panel is an integral component for optimizing network connectivity.

One of the key characteristics of the 86261-04 is its superior build quality. This patch panel is constructed with high-grade materials that ensure durability even in challenging environments. The design focuses on effective heat dissipation, allowing for extended use without the risk of overheating. This feature is particularly vital for maintaining uptime in business-critical systems.

The 86261-04 boasts a versatile port configuration, typically including multiple 10/100/1000 Mbps Ethernet ports that support various networking requirements. Its ability to auto-sense the speed of incoming connections streamlines network management and scalability. Additionally, the switch supports Power over Ethernet (PoE), enabling it to deliver power alongside connectivity to devices such as IP cameras, wireless access points, and VoIP phones. This reduces the need for additional power sources and simplifies installation.

Advanced security features are another highlight of the Allied Telesis Patch 86261-04. It incorporates VLAN capabilities, allowing network administrators to create isolated segments within the network for enhanced security. This segregation helps prevent unauthorized access and minimizes the risk of data breaches. Alongside security protocols, the switch supports Quality of Service (QoS) which prioritizes traffic according to the needs of the business, ensuring critical applications function smoothly even during peak usage times.

In terms of technology, the 86261-04 is designed with ease of configuration and management in mind. It is compatible with both command-line and web-based interfaces, providing flexibility for network administrators with varying levels of expertise. Comprehensive monitoring and reporting tools guide users in troubleshooting and optimizing network performance.

Moreover, Allied Telesis is known for its commitment to sustainability, and the 86261-04 is no exception. This model is energy-efficient, contributing to lower operating costs while maintaining high performance standards.

In summary, the Allied Telesis Patch 86261-04 stands out with its robust design, versatile port configuration, extensive network security features, and commitment to energy efficiency, making it an excellent choice for organizations looking to enhance their networking capabilities.
Top Page Image Contents