Allied Telesis at-8700xl series switch manual Virtual Local Area Networks VLANs

Page 65

Switching

65

addresses. One of the following options can be specified for the action taken when an unknown MAC address is detected on a locked port:

■Discard the packet and take no further action,

■Discard the packet and notify management with an SNMP trap,

■Discard the packet, notify management with an SNMP trap and disable the port.

Virtual Local Area Networks (VLANs)

A Virtual LAN (VLAN) is a logical, software-defined subnetwork. It allows similar devices on the network to be grouped together into one broadcast domain, irrespective of their physical position in the network. Multiple VLANs can be used to group workstations, servers, and other network equipment connected to the switch, according to similar data and security requirements.

Decoupling logical broadcast domains from the physical wiring topology offers several advantages, including the ability to:

■Move devices and people with minimal, or no, reconfiguration

■Change a device’s broadcast domain and access to resources without physically moving the device, by software reconfiguration or by moving its cable from one switch port to another

■Isolate parts of the network from other parts, by placing them in different VLANs

■Share servers and other network resources without losing data isolation or security

■Direct broadcast traffic to only those devices which need to receive it, to reduce traffic across the network

■Connect 802.1Q-compatible switches together through one port on each switch

Devices that are members of the same VLAN only exchange data with each other through the switch’s switching capabilities. To exchange data between devices in separate VLANs, the switch’s routing capabilities are used. The switch passes VLAN status information, indicating whether a VLAN is up or down, to the Internet Protocol (IP) module. IP uses this information to determine route availability.

The switch has a maximum of 255 VLANs, ranging from a VLAN identifier (VID) of 1 to 255. When the switch is first powered up, a “default” VLAN is created and all ports are added to it. In this initial unconfigured state, the switch will broadcast all the packets it receives to the default VLAN. This VLAN has a VID of 1 and an interface name of vlan1. It cannot be deleted, and ports can only be removed from it if they also belong to at least one other VLAN. The default VLAN cannot be added to any STP, but always belongs to the default STP. If all the devices on the physical LAN are to belong to the same logical LAN, that is, the same broadcast domain, then the default settings will be acceptable, and no additional VLAN configuration is required.

Software Release 2.6.1 C613-02030-00 REV B

Page 64 Page 66
Image 65
Page 64 Page 66
Contents AT-8700XL Series Switch Page Contents Switching Chapter Why Read this User Guide?AT-8700XL Series Switch Documentation Set Where To Find More InformationTechnical support Features of the AT-8700XL Series SwitchSwitching Features Layer 3 and Other Features Management FeaturesIntroduction Page This Chapter Getting Started with the Command Line Interface CLITerminal Communication Parameters Connecting a Terminal or PCAssigning an IP Address LoggingTo change the IP address for an interface, enter the command Setting Routes Choosing a Password Changing a PasswordAliases Using the CommandsSetting System Parameters Getting Command Line HelpLocation of the switch, for example Page Getting Started with the Graphical User Interface GUI Browser and PC Setup What is the GUI?Accessing the Switch via the GUI Http Proxy Servers Start here Establishing a Connection to the SwitchUse this procedure if Option 1 Configuring the Switch before InstallationTo install the switch into the same subnet as the PC Option 2 Installing the Switch into the LANEnable IP Remoteassign Option 3 Connecting to an Installed Switch To create an RSA key pair, use the command Secure AccessSet the UTC offset System Status System StatusUsing Configuration Pages Using the GUI Navigation and FeaturesConfiguration Menu An example of a configuration page with a selection table Editable Fields Ports Graphic Management MenuMonitoring Menu Diagnostics MenuChanging the Password Combining GUI and CLI Configuration Saving Configuration Entered with the GUIConfiguring Multiple Devices Context Sensitive GUI HelpUpgrading the GUI To upgrade the GUITroubleshooting Deleting Temporary Files Accessing the Switch via the GUITraffic Flow Solutions SolutionIP Addresses and Dhcp Time and NTPLoading Software Page User Accounts and Privileges Operating the switchLogin Normal Mode and Security Mode Specific Parameters Storing Files in Flash Memory Remote ManagementExample output from the Show File command Using ScriptsStoring Multiple Scripts Saving the Switch’s ConfigurationFile Naming Conventions Loading and Uploading FilesSPA Loading FilesExample Load a Patch File Using Http Setting Loader DefaultsExample Upload a Configuration File Using Tftp Uploading Files From the SwitchMore information To upload a log fileUpgrading Switch Software To upgrade to a new software release Example Upgrade to a New Software Release UsingFlash To upgrade to a new patch file Example Upgrade to a new patch fileEditor screen layout Using the Built-in EditorSnmp MIBs in the AT-8700XL Series Software Reference Snmp and MIBsFor More About Operations and Facilities Enabling and Disabling Switch Ports Switch PortsPort Trunking Autonegotiation of Port Speed and Duplex ModePacket Storm Protection Port MirroringVirtual Local Area Networks VLANs Creating VLANs Vlan Interaction with STPs and Trunk Groups Summary of Vlan tagging rulesProtected VLANs Spanning Tree Protocol STP Quality of ServiceGeneric Vlan Registration Protocol Gvrp Spanning Tree and Rapid Spanning Tree Port States IP SwitchingIgmp Snooping Routing Information Protocol RIPEvent TriggersDescription ParametersPage Maintenance and Troubleshooting Switch startup messages How the Switch Starts UpBackup software files Backup configuration script How to Avoid ProblemsWatch for software updates If you accidentally do this, you will need to What to Do if You Clear Flash Memory CompletelyGetting the Most Out of Technical Support What to Do if Passwords are LostChecking Connections Using Ping Resetting Switch DefaultsTelnet Fails Troubleshooting IP ConfigurationsUsing Trace Route for IP Traffic Troubleshooting Dhcp IP AddressesYour switch is acting as a Dhcp client Your switch is acting as a Dhcp server

at-8700xl series switch specifications

Allied Telesis AT-8700XL Series Switches are sophisticated networking devices designed to meet the demanding requirements of modern enterprise environments. These managed Ethernet switches are optimized for reliability, performance, and scalability, making them ideal for various applications, from small businesses to large-scale networks.

One of the standout features of the AT-8700XL series is its robust Layer 2 and Layer 3 capabilities. This versatility allows the switches to perform both basic switching and advanced routing functions, facilitating efficient data traffic management. The series supports a wide range of standard protocols, including VLANs, STP, and RSTP, ensuring smooth and flexible network segmentation.

Another critical characteristic is the series' high-speed connectivity options. With multiple Gigabit Ethernet ports, the AT-8700XL series can handle significant data loads, ensuring seamless communication between connected devices. Furthermore, some models within the series offer 10 Gigabit uplink ports, providing the necessary bandwidth to connect to core networks or high-speed servers.

The AT-8700XL series incorporates advanced Quality of Service (QoS) features that enable network administrators to prioritize traffic effectively. This is particularly crucial for applications sensitive to latency, such as VoIP and video conferencing. By ensuring that time-sensitive data packets are transmitted promptly, the switches help maintain optimal performance across the entire network.

Power over Ethernet (PoE) support is yet another advantage of the AT-8700XL series. This feature allows the switches to deliver power to connected devices, such as IP cameras and wireless access points, via the Ethernet cable. This capability simplifies installations by reducing the need for additional power sources, ultimately saving on costs and improving efficiency.

Security is paramount in any network, and the AT-8700XL series does not disappoint. The switches employ robust security protocols, including Access Control Lists (ACLs), MAC address filtering, and DHCP snooping, to protect against unauthorized access and ensure network integrity.

In summary, Allied Telesis AT-8700XL Series Switches offer a comprehensive solution for various networking needs. With their Layer 2 and Layer 3 capabilities, high-speed connectivity, QoS features, PoE support, and security measures, these switches are well-equipped to enhance network efficiency and reliability, making them an excellent choice for organizations looking to future-proof their infrastructure. The AT-8700XL series exemplifies Allied Telesis's commitment to delivering high-quality networking solutions that cater to the evolving demands of businesses today.
Top Page Image Contents