Paxar 9825 operating instructions 2Ethernet Operating Instructions

Page 52

3. Print a test label. See Chapter 1, “Getting Started” for more information. Press the print server test button for about a second and a label should print.

Use 6-inch long supply. If you are using supply that is shorter than 6 inches long, temporarily change your supply type to “continuous” to print the entire test label. After printing the test label, change your supply type to your previous setting.

If a label does not print, check the printer's display to see if it shows a receiving status. If so, press Escape to exit receiving mode. Once you see “Online Ready” on the display, print a test label again. If this does not print or the printer does not display “Online Ready,” the unit is locked up. Turn off the printer, wait fifteen seconds and then turn it back on.

If the printer displays “Online Ready,” but is not printing, verify that the parallel port settings did not change. The Parallel Port setting should be “Internal” and the Mode setting should be “IEEE1284”.

(From the Main Menu, select Setup, Port Settings, Parallel Comm., Port and Mode.)

4. On the test label, verify your IP and WiFi settings. If using an Ethernet cable, the “Wired/Wireless:” value should be “WIRED”. If using RF, the setting should be “WIRELESS”.

Check the “Actual SSID” and the “WiFi Sig Qual”. Is the actual SSID correct? Is the signal quality greater than zero? If the signal quality is 0, you lost connection with the access point. If it is very low, you may be experiencing interference or are very close to being out of range or an access point. A value of 100 is the best you can have for signal quality. You can probably operate at a minimum of 60, but the number of retries is likely to increase.

5. Telnet to the printer.

Note: If the print server has been reset, you may need to re-enable Telnet.

Once you have verified connectivity, Telnet to the printer. This gives you access to console operation of the printer. Press Enter (on your host) to get the “#” prompt and enter “access” as the password.

Press Enter to by-pass the user name. Once here, you have verified operation to the print server.

5-2Ethernet Operating Instructions

Image 52

Contents Print Server 802.11b/g Wired/Wireless Trademarks B L E O F C O N T E N T S Getting StartedUsing the WEB Interface Telnet Console Commands Page T T I N G S T a R T E D E r v i e wS t e m R e q u i r e m e n t s T w o r k P r o t o c o l s S u p p o r t e dE c k i n g t h e P r i n t S e r v e r H a r d w a r e R i f y i n g S u c c e s s f u l Installation Sample Test Paxar6Ethernet Operating Instructions N f i g u r i n g t h e P r i n t S e r v e r D I P S E T T I N G SF o r e Y o u B e g i n Install i n g t h e S o f t w a r e Configuring the 802.11b/g and IP Settings 4Ethernet Operating Instructions N a G E M E N T M E T H O D S N a r c h N e t C o n s o l eI X N e t w o r k C o n f i g u r a t i o n R k e l e y U N I X H o s t C o n f i g u r a t i o n Sun Solaris Configuration Name\!servicename U X C o n f i g u r a t i o n M a I X C o n f i g u r a t i o n B B r o w s e r N f i g u r a t i o n o n O t h e r S y s t e m sI N G T H E W E B I N T E R F a C E G g i n g I n N f i g u r i n g t h e P r i n t e r 4Ethernet Operating Instructions N f i g u r i n g t h e P r i n t P o r t S e t t i n g s N f i g u r i n g P r i n t S e r v i c e s T t i n g N e t W a r e P a r a m e t e r s A n g i n g T C P / I P S e t t i n g s N f i g u r i n g P r i n t r a N e t A n g i n g W i r e l e s s S e t t i n g s N f i g u r i n g a l e r t s a n d T r a p s Email Alerts12Ethernet Operating Instructions Receiving An Alert Snmp IP Traps Snmp Netware Traps A n g i n g t h e P a s s w o r d s Setting the Network Card Access Password Setting the Network Card Update Password Click Configure Network Card Update PasswordN f i g u r i n g N e t w o r k P r o t o c o l s Click Protocol ControlN t r o l l i n g I P a c c e s s To Add HostsN f i g u r i n g N e t w o r k S e c u r i t y To Remove HostsClick Configure Network Security I n t i n g a T e s t P a g e I n g t h e C o n s o l eClick Update Firmware D a t i n g F i r m w a r eS i c S e c u r i t y C o n f i g u r a t i o n s Encryption Method Type Algorithm Size Description BitsLoad the local key before enabling TLS Troubleshooting N e r a l Troubleshooting I n f o r m a t i o n2Ethernet Operating Instructions Ping ip address i.e. ping 4Ethernet Operating Instructions Troubleshooting N e t w o r k C o n f i g u r a t i o n A d i n g t h e F i r m w a r eC h n i c a l S u p p o r t L N E T C O N S O L E C O M M a N D S a 2Ethernet Operating Instructions L p C o m m a n d s Help SetDisplays a list of the available help commands for Set IP N e r a l C o m m a n d s SET PAssword SET PROTect passwordSET SERVIce servicename protocol EN/DI SET SERVIce servicename NAme newnameSHow LOAd SHow PORt name STASHow SERVEr SHow SERVEr COunters2 1 b / g W i r e l e s s C o m m a n d s SET EN Iroam DISable/STRICT/FLEXible SET EN PW passwordSET EN KEY# 1/2/3/4 SET EN Keyval WEPkeySET EN REGDOMain countrycode Country Description CodeSET EN Wpaauto ENable/DIsable SET EN SPeed 1/2/5.5/6/9/11/12/18/24/48/54SET EN Ssid ssid SET EN WEP DI/64/128P / I P C o m m a n d s SET SERVIce servicename IP EN/DI SET IP TImeout nSET IP PRObe EN/DI SET IP RArp nnM P C o m m a n d s 2 Specification s Specification ST i o n a l 8 0 2 1 b / g Specification s T i o n s O S S a R YG Absolute PathnameChannel or Glossary G-3 PSK Glossary G-5 WPA2