Paxar 9825 operating instructions 4Ethernet Operating Instructions

Page 54

T r o u b l e s h o o t i n g W i r e l e s s C o n f i g u r a t i o n P r o b l e m s

1. Make sure your computer’s wireless adapter and/or access point is configured properly and matches your print server.

2. Make sure you have a good wireless signal from your PC (if your PC is wireless) and from the print server, the printer is within range (90 meters or 300 feet), and it is away from metal objects and other devices with radio signals (Bluetooth®, 2.4 GHz cordless phones, and microwaves).

3. Make sure your computer is set to infrastructure mode if you are connecting through an access point, or Ad-Hoc (802.11) if you are connecting to the print server without an access point.

4. If you are using WEP (Wired Equivalent Privacy) or other advanced security on your wireless network, you need to temporarily disable the security on your PC in order to configure the print server. If you are using an access point with security enabled and it does not allow non- secure clients to communicate with other non-secure clients, then you also need to temporarily change the wireless mode of your computer to Ad-Hoc (802.11) mode.

Note: If no computers on your network can be set to Ad-Hoc mode, you need to temporarily disable the security on your access point. When you are done configuring the print server, you can re-enable the security on your computer and change the wireless mode back if necessary. You can also use a wired connection to configure the print server.

5. If you need to use encryption or password protect your wireless network, and your wireless adapter or access point normally uses a password or passphrase instead of WEP, it should allow you to enter 0x followed by a ten digit (for 40-bit or 64-bit WEP) or twenty-six digit (for 128-bit WEP) key in hexadecimal format (0-9 or A-F).

6. If you are experiencing slow performance or are having intermittent problems connecting, try changing the RF channel of your wireless network (Ad-Hoc mode only). This can be done in the NetMgr Wireless Configuration screen. You should change it to at least 3 channels lower or higher than any other wireless networks within range.

5-4Ethernet Operating Instructions

Image 54
Contents Print Server 802.11b/g Wired/Wireless Trademarks B L E O F C O N T E N T S Getting StartedUsing the WEB Interface Telnet Console Commands Page T T I N G S T a R T E D E r v i e wS t e m R e q u i r e m e n t s T w o r k P r o t o c o l s S u p p o r t e dE c k i n g t h e P r i n t S e r v e r H a r d w a r e R i f y i n g S u c c e s s f u l Installation Sample Test Paxar6Ethernet Operating Instructions D I P S E T T I N G S N f i g u r i n g t h e P r i n t S e r v e rF o r e Y o u B e g i n Install i n g t h e S o f t w a r e Configuring the 802.11b/g and IP Settings 4Ethernet Operating Instructions N a G E M E N T M E T H O D S N a r c h N e t C o n s o l eI X N e t w o r k C o n f i g u r a t i o n R k e l e y U N I X H o s t C o n f i g u r a t i o n Sun Solaris Configuration Name\!servicename U X C o n f i g u r a t i o n M a I X C o n f i g u r a t i o n B B r o w s e r N f i g u r a t i o n o n O t h e r S y s t e m sI N G T H E W E B I N T E R F a C E G g i n g I n N f i g u r i n g t h e P r i n t e r 4Ethernet Operating Instructions N f i g u r i n g t h e P r i n t P o r t S e t t i n g s N f i g u r i n g P r i n t S e r v i c e s T t i n g N e t W a r e P a r a m e t e r s A n g i n g T C P / I P S e t t i n g s N f i g u r i n g P r i n t r a N e t A n g i n g W i r e l e s s S e t t i n g s N f i g u r i n g a l e r t s a n d T r a p s Email Alerts12Ethernet Operating Instructions Receiving An Alert Snmp IP Traps Snmp Netware Traps A n g i n g t h e P a s s w o r d s Setting the Network Card Access Password Setting the Network Card Update Password Click Configure Network Card Update PasswordN f i g u r i n g N e t w o r k P r o t o c o l s Click Protocol ControlN t r o l l i n g I P a c c e s s To Add HostsN f i g u r i n g N e t w o r k S e c u r i t y To Remove HostsClick Configure Network Security I n t i n g a T e s t P a g e I n g t h e C o n s o l eClick Update Firmware D a t i n g F i r m w a r eS i c S e c u r i t y C o n f i g u r a t i o n s Encryption Method Type Algorithm Size Description BitsLoad the local key before enabling TLS Troubleshooting N e r a l Troubleshooting I n f o r m a t i o n2Ethernet Operating Instructions Ping ip address i.e. ping 4Ethernet Operating Instructions Troubleshooting N e t w o r k C o n f i g u r a t i o n A d i n g t h e F i r m w a r eC h n i c a l S u p p o r t L N E T C O N S O L E C O M M a N D S a 2Ethernet Operating Instructions L p C o m m a n d s Help SetDisplays a list of the available help commands for Set IP N e r a l C o m m a n d s SET SERVIce servicename protocol EN/DI SET PAsswordSET PROTect password SET SERVIce servicename NAme newnameSHow SERVEr SHow LOAdSHow PORt name STA SHow SERVEr COunters2 1 b / g W i r e l e s s C o m m a n d s SET EN KEY# 1/2/3/4 SET EN Iroam DISable/STRICT/FLEXibleSET EN PW password SET EN Keyval WEPkeySET EN REGDOMain countrycode Country Description CodeSET EN Ssid ssid SET EN Wpaauto ENable/DIsableSET EN SPeed 1/2/5.5/6/9/11/12/18/24/48/54 SET EN WEP DI/64/128P / I P C o m m a n d s SET IP PRObe EN/DI SET SERVIce servicename IP EN/DISET IP TImeout n SET IP RArp nnM P C o m m a n d s Specification S 2 Specification sT i o n a l 8 0 2 1 b / g Specification s T i o n s O S S a R YG Absolute PathnameChannel or Glossary G-3 PSK Glossary G-5 WPA2