Rose electronic CrystalView Plus manual Only video is required, but no picture appears

Page 35

Only video is required, but no picture appears.

nThe probable cause is that power to the Local Unit is not applied. The Local Unit obtains its power from the CPUs keyboard port. A keyboard cable must be connected from the Local Unit to the CPU even if no keyboard is required. A supplementary power supply can be obtained that connects to the Local Units keyboard connector.

System does not detect a PS/2 mouse

nKeyboard and mouse cables reversed on the Local Unit.

nCable is loose; re-seat mouse cable on the CPU and the Local Unit.

nEnsure that the keyboard cable to the Local Unit is connected to provide adequate power to the Local Unit.

nIf you are connecting the local unit to a CPU with power applied, connect the mouse cable to the CPU before you connect the keyboard cable to ensure the mouse is correctly detected.

nRe-boot PC.

Keyboard error on boot-up

nPress [F1] or [Esc] and if this corrects the problem, modify the BIOS setting to disable keyboard testing during boot-up.

No sound at the Remote Units speakers or headphones.

nAudio cable loose or defective.

nAudio cable in the wrong connector.

nSound card “Line Out” muted.

No sound at the CPUs speakers when using a Microphone on the Remote Unit.

nMicrophone cable in wrong connector.

nSound card “MIC” input muted.

nMicrophone signal not amplified; increase sound card amplification by +20db. Add “MIC” jumper on the Remote Units daughter board to increase signal. Do not add this jumper if the microphone is already a powered microphone.

Serial device does not function

nSerial cable loose or defective.

nFlow control incorrectly set on unit or CPU.

nConnect serial device directly to the CPU’s serial port and check to determine if the problem is a PC or CrystalView Plus problem.

CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL

 

 

29

 

 

 

 

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents CrystalView Plus Limited Warranty FCC/IC STATEMENTS, EU Declaration of Conformity Page Table of Contents Figures System introduction IntroductionDisclaimer Features Rose Electronics web site About this manual Package contentsCompatibility Single video Local models ModelsDB9M Single video Remote modelsRear Remote Rear remote with serial/audioRear Local with serial/audio Dual video local modelsRear Local DB25FDual video Remote models Dual video remote modelsQuad video Remote models Quad video remote modelsCables CablesAudio cable Do not Install the MIC JumperSerial cable Installation InstallationSerial/audio models Connecting the cablesLocal KVM access models Local unit to CPU cablingSerial port Do not Install the MIC Jumper if Using a Powered MicrophoneRemote unit to KVM station cabling Local unit to Remote unit cablingDual video cabling Dual Video cablingRemote unit to KVM station cabling Quad Video Remote Unit cabling All models Connecting to a Rose KVM switchApplying power Command Key Sequence Keyboard CommandsKeyboard commands Select Channel 1 Keyboard command descriptionsExit Command mode and save Esc Exit Command mode without saving L-Shift + ESCIncrease RED delay R + R-Arrow Reset EQ & Delay values L-Ctrl + HomeNext Assisted EQ setting L-Ctrl + PgUp Previous Assisted EQ setting L-Ctrl + PgDnIncrease LF EQ Course L + Up Arrow Toggle RED delay L-Ctrl + RToggle Green delay L-Ctrl + G Toggle Blue delay L-Ctrl + BToggle Unit Private Mode Scroll Lock Local unit Keyboard commands Dual local model onlyReset keyboard and mouse F1 Reset to factory defaults L-Ctrl + F9Send Null mouse byte Reset the local keyboard and mouseRED Green Blue Video AdjustmentsAdjusting the video HF / LF adjustment guide Blue Operating instructions- All units KVM SwitchingPrivate mode Dual access models only Operating InstructionsTroubleshooting TroubleshootingSystem does not detect a PS/2 mouse Keyboard error on boot-upNo sound at the Remote Units speakers or headphones Only video is required, but no picture appearsTechnical Support Service InformationMaintenance and Repair Safety SafetyServicing Safety and EMC Regulatory StatementsGrounding Appendices Appendix A. General specificationsCrystalview Plus Installation and Operations Manual Part Number Description Appendix B. Parts and cablesAppendix C. Rack mount instructions Appendix D. Rack mount illustration Appendix E. Quick Installation/Setup Guide Crystalview Plus Installation and Operations Manual Crystalview Plus Installation and Operations Manual Page Stancliff Road Houston, Texas Phone 281

CrystalView Plus specifications

The Rose Electronic CrystalView Plus is a state-of-the-art KVM (Keyboard, Video, Mouse) switch that is designed to streamline the control of multiple computers from a single workstation. This sophisticated device is particularly beneficial in environments such as data centers, control rooms, and server management operations, where efficiency and space utilization are paramount.

One of the standout features of the CrystalView Plus is its ability to support a wide range of platforms, including Windows, macOS, and Linux. This versatility means that users can seamlessly switch between different systems without the need for additional adapters or cables. The CrystalView Plus also supports multiple video resolutions up to 4K, ensuring high-quality visuals that enhance the user experience, especially for those working with graphics-intensive applications.

The CrystalView Plus employs advanced technologies to ensure reliability and performance. With its innovative autosensing technology, the device automatically detects connected computers and optimally configures the necessary settings, making it user-friendly even for those who are not technically inclined. Additionally, the KVM switch features a hotkey switching function that allows users to toggle between computers quickly and efficiently, saving valuable time during critical tasks.

The device is built with robust construction that ensures durability and longevity in demanding environments. Its compact design allows for easy integration into existing setups, minimizing the footprint without compromising on functionality. With support for both USB 2.0 and USB 3.0 devices, users can conveniently connect peripherals such as external hard drives, printers, and scanners, enhancing productivity by allowing access to various resources from one central location.

Security is another critical aspect of the CrystalView Plus, as it isolates computer systems from each other, preventing unauthorized access and potential data breaches. This feature is incredibly important in sensitive environments where data integrity and confidentiality are crucial.

In terms of connectivity, the CrystalView Plus includes multiple input/output options and supports both VGA and HDMI connections, catering to a range of user needs. The intuitive LED indicators provide real-time status updates for connected systems, allowing users to monitor their setup at a glance.

In summary, the Rose Electronic CrystalView Plus KVM switch stands out due to its user-friendly design, high compatibility with various operating systems, superior video quality, and robust security features. This makes it an ideal solution for anyone looking to enhance their operational efficiency in managing multiple computer systems.
Top Page Image Contents