Panduit PTR3E manual Backfeed Offset, Display, Print

Page 44

have enough range, then you will have to change the pitch setting using the LCD front panel display.

6.Press the FEED key to stop the printer.

7.To exit the Test Label mode, power the printer off and then back on. Adjusting the PITCH potentiometer will affect the stop position of the label.

BACKFEED OFFSET

When a label is printed it must be correctly positioned for dispensing and application. The Backfeed adjustment is used to position the label so that it is fully dispensed and ready for application. It may then be necessary to reposition the next label before printing. The Backfeed (repositioning of the label) operation is enabled if DSW3-4 is in the Off position. If backfeed is enabled, placing DSW3-1 in the Off position will cause the backfeed operationto be performed immediately before each label is printed. If DSW3-1 is in the On position, the backfeed operation is performed as soon as the dispensed label has been printed and taken from the printer.

The amount of backfeed is controlled by the OFFSET potentiometer on the DIP Switch Panel inside the cover. When turned all the way counterclockwise, the amount of backfeed is +3.75 mm, and -3.75 mm when turned all the way counterclockwise.

1.Turn the printer on.

2.Press the LINE key to place the printer in the Off Line status.

3.Press the FEED key to feed out a blank label.

4.Adjust the position using the OFFSET potentiometer on the front control panel and feed another label by depressing the FEED key. Repeat this procedure until the label is fully released from the liner.

DISPLAY

This potentiometer is used to adjust the contrast of the LCD display for optimum viewing under various lighting conditions.

PRINT

The PRINT potentiometer is used to adjust the amount of heat (i.e., power) applied to the head for printing. It provides a continuous range of adjustment. Maximum print darkness is obtained by turning the potentiometer all the way clockwise and a maximum counterclockwise setting will give the lightest print.

 

NOTE: The PRINT potentiometer adjustment will affect the darkness in all of the

36

commend code speed and darkness ranges.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Operator and Technical Reference Manual Panduit PTR3E Safety Practices Information to User Warranty Information PTR3E Operator Manual Table of Contents IEEE1284 Parallel Interface RS232C Serial Interface Page Section Printer Overview IntroductionGeneral Printer Specifications Specification PTR3EPotentiometer Adjustments Character Fonts Matrix FontsBAR Codes MSI Postnet UCC/EAN-128Power Requirements PhysicalSection Installation Here,butarethe OperatorManual ExtraRibbonCore Door PTR3E Follow these steps to properly load labels intoPage Sensor Loading THERibbonSpindleRIBBONRewind Page Label Use Page Page Label Sensor Adjustment DIP Switch Panels Printer Set UpOFFON123DSW245678 Print Speed Adjustment DSW2-8 . See Mode SelectionExternal Repeat Print via Ex erDefault S Tti gs Protocol SelectiPrinter Adjustments Print Speed InitializingOnline QTY000000 Offline Pitch Offset ± 00mmInitializing ROM Advanced Mode Zero Slash YES no Auto Online Print Offset Ignore CR/LF YES noCharacter Pitch Prop Fixed Advanced Mode Service ModeAdvanced Mode Service Mode GAP InputAuto Online Feed YES no Feed on Error Reprint W/FEED FORWARD/BACKFEED Distance DefaultFORWARD/BACKFEED Distance XXXmm Euro Code Select Language EnglishService Mode Test Print Mode Priority Setting Command LCDDefault Setting Mode Default Setting YES noDefault Setting Completed Initializing ROMHEX Dump Mode Potentiometer AdjustmentsInitializing ROM Online QTY000000 PitchPrint Backfeed OffsetDisplay Factory Mode Maintenance Mode DIPSW2-4 ON-OFFDisplay Counter Values Counter Clear NonePage Darkness Print ProceduresAdjusting the Print Quality Print,thedarkness Cleaning the Print HEAD, Platen and Rollers Cleaning the Print Head and PlatenCleaning the Sensors Cleaning the Rollers and GuidesOpen the Top and Side Access doors Replacing the Print HeadThed,centeritwill Replacing the Fuse Supplies neededCleaning and Maintenance IEEE1284 Parallel Interface Electrical SpecificationsInterface Types General Specifications RS232C Serial InterfaceInitial Checklist Using the IEEE1284 Parallel InterfaceUsing the RS232C Serial Interface TroubleshootingError Signals LED LCD Audible Error Condition To Clear Message Beep

PTR3E specifications

The Panduit PTR3E is a key player in the realm of cable management and network infrastructure solutions, designed to meet the evolving demands of modern telecommunications and data center environments. This innovative product is part of Panduit's extensive lineup, which is known for robustness, efficiency, and versatility.

One of the standout features of the PTR3E is its exceptional modular design. This modularity allows for straightforward installation and easy reconfiguration as network demands change. The PTR3E supports a wide array of mounting options, making it suitable for various installations, from wall-mounted system configurations to versatile rack setups. This flexibility ensures that it can fit seamlessly into existing infrastructures while providing the capability to scale efficiently.

Another significant characteristic of the PTR3E is its use of advanced materials. Constructed from high-quality, durable plastics, it offers excellent resistance to environmental factors including temperature variations and humidity, which are common challenges in data centers and network closets. This resilience not only increases the lifespan of the product but also minimizes maintenance costs and downtime.

In terms of technology, the PTR3E is engineered to support high-density fiber and copper cabling solutions. It can accommodate a variety of cable types, ensuring compatibility with different systems and reducing the clutter that often hampers network efficiency. The intelligent design features integrated strain relief and cable management capabilities that help in organizing cables without imposing undue stress on connectors and ports.

Moreover, the PTR3E is designed with user operation in mind. Its intuitive design facilitates easy access to cables and ports, allowing for quicker troubleshooting and upgrades. This accessibility is critical in fast-paced environments where time is of the essence, making it a preferred choice for IT professionals.

Furthermore, the PTR3E adheres to the latest industry standards, ensuring compliance with regulatory requirements. This reliability is crucial for organizations that prioritize system integrity and performance. With the integration of Panduit's technology, the PTR3E not only enhances operational efficiency but also aligns with sustainability goals, reducing environmental impact in systems design.

In conclusion, the Panduit PTR3E is a versatile, durable, and technologically advanced solution for cable management in today’s fast-paced networking environments. Its modularity, high-quality materials, and thoughtful design make it an essential component for any organization looking to optimize its network infrastructure.
Top Page Image Contents