Panduit PTR3E manual Safety Practices

Page 3

This manual will guide you step by step in the set-up, operation, and troubleshooting of the PTR3E Printer. If you have problems not covered call Technical Support at 1-888-506-5400, ext. 7470.

SAFETY PRACTICES

The following general safety practices supplement the specific warnings and cautions elsewhere in this manual. They are recommended precautions that must be understood and applied during the operation and maintenance of the equipment covered herein.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the product in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

DO NOT OPERATE IN WET OR DAMP AREAS

Do not operate the product in wet or damp areas. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT

Because of the danger of introducing additional hazards, do not install substitute parts or perform an unauthorized modification to the equipment. The proper components for service and repair may be obtained from Panduit Corp., Labeling Systems Department, 1-888-506-5400, ext. 7470. The product may also be returned for service and repair by calling the above number and requesting a Tracking Number. Please provide your company name, contact name, address, telephone number and serial number of the printer (and P.O. Number if out of warranty) when requesting the Tracking Number. After Tracking Number is received the printer should be returned to :

Panduit Corp.

1819 Atlanta Highway

Cumming, GA 30040-1069

Attention: Labeling Systems Repair Department

WARNING

When the printer has been in use for a long time, the print head may become hot. DO NOT touch the print head with bare hands.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Operator and Technical Reference Manual Panduit PTR3E Safety Practices Information to User Warranty Information PTR3E Operator Manual Table of Contents IEEE1284 Parallel Interface RS232C Serial Interface Page Introduction Section Printer OverviewSpecification PTR3E General Printer SpecificationsPotentiometer Adjustments Matrix Fonts Character FontsMSI Postnet UCC/EAN-128 BAR CodesPhysical Power RequirementsSection Installation Here,butarethe OperatorManual ExtraRibbonCore Door Follow these steps to properly load labels into PTR3EPage Sensor Loading THERibbonSpindleRIBBONRewind Page Label Use Page Page Label Sensor Adjustment Printer Set Up DIP Switch PanelsOFFON123DSW245678 Mode Selection Print Speed Adjustment DSW2-8 . SeeRepeat Print via Ex er ExternalProtocol Selecti Default S Tti gsPrinter Adjustments Initializing Online QTY000000 OfflinePrint Speed ± 00mm Pitch OffsetInitializing ROM Advanced Mode Zero Slash YES no Auto Online Ignore CR/LF YES no Print OffsetGAP Input Character Pitch Prop Fixed Advanced ModeService Mode Advanced Mode Service ModeEuro Code Select Language English Auto Online Feed YES no Feed on Error Reprint W/FEEDFORWARD/BACKFEED Distance Default FORWARD/BACKFEED Distance XXXmmPriority Setting Command LCD Service Mode Test Print ModeInitializing ROM Default Setting ModeDefault Setting YES no Default Setting CompletedPitch HEX Dump ModePotentiometer Adjustments Initializing ROM Online QTY000000Backfeed Offset DisplayPrint Counter Clear None Factory ModeMaintenance Mode DIPSW2-4 ON-OFF Display Counter ValuesPage Procedures Adjusting the Print QualityDarkness Print Print,thedarkness Cleaning the Print Head and Platen Cleaning the Print HEAD, Platen and RollersCleaning the Rollers and Guides Cleaning the SensorsReplacing the Print Head Open the Top and Side Access doorsThed,centeritwill Supplies needed Replacing the FuseCleaning and Maintenance Electrical Specifications Interface TypesIEEE1284 Parallel Interface RS232C Serial Interface General SpecificationsUsing the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceLED LCD Audible Error Condition To Clear Message Beep Error Signals

PTR3E specifications

The Panduit PTR3E is a key player in the realm of cable management and network infrastructure solutions, designed to meet the evolving demands of modern telecommunications and data center environments. This innovative product is part of Panduit's extensive lineup, which is known for robustness, efficiency, and versatility.

One of the standout features of the PTR3E is its exceptional modular design. This modularity allows for straightforward installation and easy reconfiguration as network demands change. The PTR3E supports a wide array of mounting options, making it suitable for various installations, from wall-mounted system configurations to versatile rack setups. This flexibility ensures that it can fit seamlessly into existing infrastructures while providing the capability to scale efficiently.

Another significant characteristic of the PTR3E is its use of advanced materials. Constructed from high-quality, durable plastics, it offers excellent resistance to environmental factors including temperature variations and humidity, which are common challenges in data centers and network closets. This resilience not only increases the lifespan of the product but also minimizes maintenance costs and downtime.

In terms of technology, the PTR3E is engineered to support high-density fiber and copper cabling solutions. It can accommodate a variety of cable types, ensuring compatibility with different systems and reducing the clutter that often hampers network efficiency. The intelligent design features integrated strain relief and cable management capabilities that help in organizing cables without imposing undue stress on connectors and ports.

Moreover, the PTR3E is designed with user operation in mind. Its intuitive design facilitates easy access to cables and ports, allowing for quicker troubleshooting and upgrades. This accessibility is critical in fast-paced environments where time is of the essence, making it a preferred choice for IT professionals.

Furthermore, the PTR3E adheres to the latest industry standards, ensuring compliance with regulatory requirements. This reliability is crucial for organizations that prioritize system integrity and performance. With the integration of Panduit's technology, the PTR3E not only enhances operational efficiency but also aligns with sustainability goals, reducing environmental impact in systems design.

In conclusion, the Panduit PTR3E is a versatile, durable, and technologically advanced solution for cable management in today’s fast-paced networking environments. Its modularity, high-quality materials, and thoughtful design make it an essential component for any organization looking to optimize its network infrastructure.
Top Page Image Contents