Panduit PTR3E manual Initial Checklist, Using the IEEE1284 Parallel Interface

Page 57

SECTION 6.

TROUBLESHOOTING

This section has been compiled to help you produce output on the PTR3E. Use this section to make sure the basics have been checked before deciding you are unable to proceed any further. The section is divided into four parts:

•Initial Checklist

•IEEE1284 Parallel Interface

•RS232C Serial Interface

•Error Signals

INITIAL CHECKLIST

1.Is the printer powered up and On-Line?

2.Is the ERROR light on the front panel off? If this light is on, it may mean the Print Head Assembly or the Label Hold-Down is not closed and latched in position.

3.Are the LABEL and RIBBON lights on the front panel off? If these lights are on, the labels or ribbons may be incorrectly loaded.

USING THE IEEE1284 (PARALLEL) INTERFACE

1.Is the IEEE1284 parallel printer cable connected securely to your parallel port (DB-25S Female) on the PC and to the IEEE1284 connector on the printer?

WARNING: Never connect or disconnect interface cables (or use a switch box) with power applied to either the printer or the host. This may cause damage to the interface circuitry and is not covered by warranty.

2Does the Parallel interface cable used meet IEEE1284 specifications? If it does not and you are connected to an IEEE1284 or ECP parallel port on the computer, the printer may not be able to communicate correctly.

3.Is there more than one parallel interface port on your PC (LPT1, LPT2, etc.)? If so, make sure you are sending data out the correct port.

4.Is the IEEE1284 Interface Module installed in the printer? The PTR3E requires the new IEEE1284 Parallel Interface (PN WCL40470) to take advantage of the faster data transmission speeds. The older Parallel Interface Modules will work, but at a reduced capability.

49

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Operator and Technical Reference Manual Panduit PTR3E Safety Practices Information to User Warranty Information PTR3E Operator Manual Table of Contents IEEE1284 Parallel Interface RS232C Serial Interface Page Introduction Section Printer OverviewSpecification PTR3E General Printer SpecificationsPotentiometer Adjustments Matrix Fonts Character FontsMSI Postnet UCC/EAN-128 BAR CodesPhysical Power RequirementsSection Installation Here,butarethe OperatorManual ExtraRibbonCore Door Follow these steps to properly load labels into PTR3EPage Sensor Loading THERibbonSpindleRIBBONRewind Page Label Use Page Page Label Sensor Adjustment Printer Set Up DIP Switch PanelsOFFON123DSW245678 Mode Selection Print Speed Adjustment DSW2-8 . SeeRepeat Print via Ex er ExternalProtocol Selecti Default S Tti gsPrinter Adjustments Initializing Online QTY000000 OfflinePrint Speed ± 00mm Pitch OffsetInitializing ROM Advanced Mode Zero Slash YES no Auto Online Ignore CR/LF YES no Print OffsetService Mode Character Pitch Prop Fixed Advanced ModeAdvanced Mode Service Mode GAP InputFORWARD/BACKFEED Distance Default Auto Online Feed YES no Feed on Error Reprint W/FEEDFORWARD/BACKFEED Distance XXXmm Euro Code Select Language EnglishPriority Setting Command LCD Service Mode Test Print ModeDefault Setting YES no Default Setting ModeDefault Setting Completed Initializing ROMPotentiometer Adjustments HEX Dump ModeInitializing ROM Online QTY000000 PitchBackfeed Offset DisplayPrint Maintenance Mode DIPSW2-4 ON-OFF Factory ModeDisplay Counter Values Counter Clear NonePage Procedures Adjusting the Print QualityDarkness Print Print,thedarkness Cleaning the Print Head and Platen Cleaning the Print HEAD, Platen and RollersCleaning the Rollers and Guides Cleaning the SensorsReplacing the Print Head Open the Top and Side Access doorsThed,centeritwill Supplies needed Replacing the FuseCleaning and Maintenance Electrical Specifications Interface TypesIEEE1284 Parallel Interface RS232C Serial Interface General SpecificationsUsing the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceLED LCD Audible Error Condition To Clear Message Beep Error Signals

PTR3E specifications

The Panduit PTR3E is a key player in the realm of cable management and network infrastructure solutions, designed to meet the evolving demands of modern telecommunications and data center environments. This innovative product is part of Panduit's extensive lineup, which is known for robustness, efficiency, and versatility.

One of the standout features of the PTR3E is its exceptional modular design. This modularity allows for straightforward installation and easy reconfiguration as network demands change. The PTR3E supports a wide array of mounting options, making it suitable for various installations, from wall-mounted system configurations to versatile rack setups. This flexibility ensures that it can fit seamlessly into existing infrastructures while providing the capability to scale efficiently.

Another significant characteristic of the PTR3E is its use of advanced materials. Constructed from high-quality, durable plastics, it offers excellent resistance to environmental factors including temperature variations and humidity, which are common challenges in data centers and network closets. This resilience not only increases the lifespan of the product but also minimizes maintenance costs and downtime.

In terms of technology, the PTR3E is engineered to support high-density fiber and copper cabling solutions. It can accommodate a variety of cable types, ensuring compatibility with different systems and reducing the clutter that often hampers network efficiency. The intelligent design features integrated strain relief and cable management capabilities that help in organizing cables without imposing undue stress on connectors and ports.

Moreover, the PTR3E is designed with user operation in mind. Its intuitive design facilitates easy access to cables and ports, allowing for quicker troubleshooting and upgrades. This accessibility is critical in fast-paced environments where time is of the essence, making it a preferred choice for IT professionals.

Furthermore, the PTR3E adheres to the latest industry standards, ensuring compliance with regulatory requirements. This reliability is crucial for organizations that prioritize system integrity and performance. With the integration of Panduit's technology, the PTR3E not only enhances operational efficiency but also aligns with sustainability goals, reducing environmental impact in systems design.

In conclusion, the Panduit PTR3E is a versatile, durable, and technologically advanced solution for cable management in today’s fast-paced networking environments. Its modularity, high-quality materials, and thoughtful design make it an essential component for any organization looking to optimize its network infrastructure.
Top Page Image Contents