Panduit PTR3E manual Display Counter Values, Factory Mode, Counter Clear None

Page 45

DISPLAY COUNTER VALUES

The internal counters are used to track the number of kilometers of media that has been processed through the printer, the number of labels cut and/or the number of label dispensed. These values can be used to track component life for service and maintenance functions. The current counter settings are displayed on the Factory/Service mode Test Label. To print the Factroy/Service Test Label, the following procedure must be used:

1.Turn the printer OFF and place DSW2-4in the ON position.

2.Open the print head by releasing the Head Latch.

3.While simultaneously pressing the LINE and FEED keys, turn the printer ON.

4.Close and latch the print head.

5.The LCD panel should read:

MAINTENANCE MODE

DIPSW2-4 ON->OFF

6.Place DSW2-4in the OFF position.

7.The LCD panel should indicate that the printer is in the FACTORY MODE.

FACTORY MODE

8.Press the FEED key and the display will advance to the COUNTER CLEAR message screen. Make sure that the NONE selection is displayed on the bottom line. If it is not, press the LINE key once until ALL is displayed.

COUNTER CLEAR

NONE

9.Press the FEED key to initiate the Test Label print mode. Then press the LINE key to begin printing Test Labels. The printer will print Test Labels continuously until the FEED key is pressed again, which pauses the printer. Test Labels will again start printing as soon as the FEED key is pressed again.

WARNING: The Test Label is designed to print on a full width label. If smaller labels are used, the print head may be damaged if more than one label is printed.

10.The counter readings and ROM version are printed on the label along with other pertinent information.

11.Turn the unit OFF and reset the DIP switches to the proper operating

positions before powering the printer back ON.

37

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Operator and Technical Reference Manual Panduit PTR3E Safety Practices Information to User Warranty Information PTR3E Operator Manual Table of Contents IEEE1284 Parallel Interface RS232C Serial Interface Page Introduction Section Printer OverviewSpecification PTR3E General Printer SpecificationsPotentiometer Adjustments Matrix Fonts Character FontsMSI Postnet UCC/EAN-128 BAR CodesPhysical Power RequirementsSection Installation Here,butarethe OperatorManual ExtraRibbonCore Door Follow these steps to properly load labels into PTR3EPage Sensor Loading THERibbonSpindleRIBBONRewind Page Label Use Page Page Label Sensor Adjustment Printer Set Up DIP Switch PanelsOFFON123DSW245678 Mode Selection Print Speed Adjustment DSW2-8 . SeeRepeat Print via Ex er ExternalProtocol Selecti Default S Tti gsPrinter Adjustments Initializing Online QTY000000 OfflinePrint Speed ± 00mm Pitch OffsetInitializing ROM Advanced Mode Zero Slash YES no Auto Online Ignore CR/LF YES no Print OffsetService Mode Character Pitch Prop Fixed Advanced ModeAdvanced Mode Service Mode GAP InputFORWARD/BACKFEED Distance Default Auto Online Feed YES no Feed on Error Reprint W/FEEDFORWARD/BACKFEED Distance XXXmm Euro Code Select Language EnglishPriority Setting Command LCD Service Mode Test Print ModeDefault Setting YES no Default Setting ModeDefault Setting Completed Initializing ROMPotentiometer Adjustments HEX Dump ModeInitializing ROM Online QTY000000 PitchBackfeed Offset DisplayPrint Maintenance Mode DIPSW2-4 ON-OFF Factory ModeDisplay Counter Values Counter Clear NonePage Procedures Adjusting the Print QualityDarkness Print Print,thedarkness Cleaning the Print Head and Platen Cleaning the Print HEAD, Platen and RollersCleaning the Rollers and Guides Cleaning the SensorsReplacing the Print Head Open the Top and Side Access doorsThed,centeritwill Supplies needed Replacing the FuseCleaning and Maintenance Electrical Specifications Interface TypesIEEE1284 Parallel Interface RS232C Serial Interface General SpecificationsUsing the IEEE1284 Parallel Interface Initial ChecklistTroubleshooting Using the RS232C Serial InterfaceLED LCD Audible Error Condition To Clear Message Beep Error Signals

PTR3E specifications

The Panduit PTR3E is a key player in the realm of cable management and network infrastructure solutions, designed to meet the evolving demands of modern telecommunications and data center environments. This innovative product is part of Panduit's extensive lineup, which is known for robustness, efficiency, and versatility.

One of the standout features of the PTR3E is its exceptional modular design. This modularity allows for straightforward installation and easy reconfiguration as network demands change. The PTR3E supports a wide array of mounting options, making it suitable for various installations, from wall-mounted system configurations to versatile rack setups. This flexibility ensures that it can fit seamlessly into existing infrastructures while providing the capability to scale efficiently.

Another significant characteristic of the PTR3E is its use of advanced materials. Constructed from high-quality, durable plastics, it offers excellent resistance to environmental factors including temperature variations and humidity, which are common challenges in data centers and network closets. This resilience not only increases the lifespan of the product but also minimizes maintenance costs and downtime.

In terms of technology, the PTR3E is engineered to support high-density fiber and copper cabling solutions. It can accommodate a variety of cable types, ensuring compatibility with different systems and reducing the clutter that often hampers network efficiency. The intelligent design features integrated strain relief and cable management capabilities that help in organizing cables without imposing undue stress on connectors and ports.

Moreover, the PTR3E is designed with user operation in mind. Its intuitive design facilitates easy access to cables and ports, allowing for quicker troubleshooting and upgrades. This accessibility is critical in fast-paced environments where time is of the essence, making it a preferred choice for IT professionals.

Furthermore, the PTR3E adheres to the latest industry standards, ensuring compliance with regulatory requirements. This reliability is crucial for organizations that prioritize system integrity and performance. With the integration of Panduit's technology, the PTR3E not only enhances operational efficiency but also aligns with sustainability goals, reducing environmental impact in systems design.

In conclusion, the Panduit PTR3E is a versatile, durable, and technologically advanced solution for cable management in today’s fast-paced networking environments. Its modularity, high-quality materials, and thoughtful design make it an essential component for any organization looking to optimize its network infrastructure.
Top Page Image Contents