Peavey GT, TC owner manual Aux 8 Direct Switch, Scene Mute Assignments, Scene Mute Safe Switch

Page 15

CENTURY SERIES

SP / TC / GT

Aux 8 Direct Switch

Removes the Aux 8 signal from the Aux 8 bus and assigns to the direct out 1/4" connector on the rear panel.

PRE/POST Switch

Selects the Aux 5 through 8 signal sources between pre and post fader positions.

PAN CONTROL

Scene Mute Assignments

Assign the input channel to any of the four scene mute groups. Scene mute combines with the module’s local mute button, and actuates the local mute LED.

Scene Mute Safe Switch

Disables any selected scene mute assignments. An associated green LED indicates the channel is in a safe state.

Positions the channel image between the left (odd) and right (even) channel assignment.

MUTE Switch with LED

Mutes the channel and all send functions. This switch does not affect the PFL switch or the Peak and Signal Present LED indi- cators. The LED illuminates when the channel is muted from the local mute switch.

MONO Bus Assign Switch

Assigns the input signal directly to the Mono Clean bus.

Bus Assign Switches (L/R, 1-8)

Assigns the post Pan Signals to the mix bus in odd/even pairs. Pan controls assignment between these two mix buses with extreme left pan assigning signal exclusively to the odd mix bus and extreme right pan assigning signal exclusively to the even mix bus. When the pan is in its center position, signal is fed equally to the odd (left) and even (right) mix bus. When used in stereo applications, the channel signal may be located anywhere within the stereo image as controlled by the Pan con- trol.

PFL Switch

Samples the channel’s signal pre-fader and allows for monitor- ing within the master section of the console. This signal is not affected by the Mute Switch. When depressed, the signal level can be seen on the Left/Right meters, and heard via the mixer’s headphone or local monitor output. When this PFL Switch is depressed, the channel PEAK LED indicator illuminates at a lower intensity. When used as a status indicator of switch posi- tion, the Peak LED indicating circuit remains fully operational by illuminating at a much higher intensity than its use as a PFL status indicator.

PEAK LED Indicator

Illuminates RED when any of the points monitored come with- in 3db of the clipping point. Signal is sampled after the input preamplifier stage, after the EQ section, and after the fader.

This LED also serves as a PFL ON indicator, but at a much lower intensity than when it is used to indicate clipping.

SIGNAL PRESENT LED

Constantly displays level activity of the input channel by vary- ing in intensity.

100mm Fader

Used for control of all outputs of the channel except those Aux output sections selected by switch to a pre fader position. (The Insert output level is not affected by the fader position.)

DIR OUT

INSERT

BAL LINE IN

BALMIC IN

Rear Connections

Direct Out

This jack provides the direct output signal (post fader & post mute) from the associat- ed input channel.

Insert

This jack allows for the insertion of an effect or signal processor into the audio path of the associated input channel.

Bal Line In

This jack accepts balanced and unbalanced line level inputs and delivers it into the associated input channel.

Bal Mic In

This connector accepts balanced micro- phone inputs for the associated input chan- nel.

PAGE 13

Image 15
Contents SP TC GT Crest Audio Inc Table of Contents Feature Overview Input XLR Output XLR Wiring ConventionsCentury Series Console Power Supply To Console Power ConnectionsSystem Connections Signal Processors SP Input Module Rear Connections MID EQ Level and Sweep Controls Polarity Reverse SwitchTC Input Module HF Equalizer ControlPAN Control Four-Band Sweep Equalizer Controls PEAK/SHELVE HF SwitchPEAK/SHELVE LF Switch GT Input ModuleAux 8 Direct Switch Scene Mute Safe SwitchScene Mute Assignments Gain & R Gain Controls XLR PAD SwitchStereo Switch GT Stereo Input ModulePEAK/PFL LED Indicator Width ControlBAL Control Group SP/TC Group Modules GT Group Module Matrix Levels A, BEffect Aux Sends Fader Reverse w/LED EFX Return Scene Mute Safe SwitchGroup XLR Matrix Pre/PostMatrix Matrix AUX Mains Mono Matrix Module Talk Back SP/TC Master Section Monitor GT Master Section GT Master Section contd GT TC SP General Specifications SP Console ConfigurationsArchitect’s & Engineer’s Specifications SP Console TC Consoles are available in the following configurations GT Consoles are available in the following configurations GT/TC Side Dimensions GT rear view shown Rear Views & DimensionsSP/TC/GT USER-OPTIONS Three Remove rear screws Console DisassemblyONE Open the armrest TWO Remove top module screwPage SP TC GT Auxiliary Mute Switches 100mm Fader See Fader 48 Volt Phantom PowerAuxiliary 34 Switch Auxiliary 8 Direct SwitchHigh Pass Switch Fader Reverse SwitchGroup XLR Switch HF Peak/Shelve SwitchMute Switch LF Peak/Shelve SwitchMatrix Pre/Post Switch SwitchScene Mute Safe Switch w/LED Phantom PowerPolarity Reverse Switch Pre/Post Fader Switch Scene Mute Assignment SwitchSP / TC / GT Appendix C Schematics Crest Audio Inc