Peavey GT, TC owner manual PAN Control

Page 13

CENTURY SERIES

SP / TC / GT

PAN CONTROL

Positions the channel image between the left (odd) and right (even) channel assignment.

MUTE Switch with LED

Mutes the channel and all send functions. This switch does not affect the PFL switch or the Peak and Signal Present LED indi- cators. The LED illuminates when the channel is muted from the local mute switch or mute scene masters.

MONO Bus Assign Switch

Assigns the post-fader input signal directly to the Mono Clean bus.

Bus Assign Switches (L/R, 1-8)

Assigns the post Pan Signals to the mix bus in odd/even pairs. Pan controls assignment between these two mix buses with extreme left pan assigning signal exclusively to the odd mix bus and extreme right pan assigning signal exclusively to the even mix bus. When the pan is in its center position, signal is fed equally to the odd (left) and even (right) mix bus. When used in stereo applications, the channel signal may be located anywhere within the stereo image as controlled by the Pan con- trol.

PFL Switch

Samples the channel’s signal pre-fader and allows for monitor- ing within the master section of the console. This signal is not affected by the Mute Switch. When depressed, the signal level can be seen on the Left/Right meters, and heard via the mixer’s headphone or local monitor output. When this PFL Switch is depressed, the channel PEAK LED indicator illuminates at a lower intensity. When used as a status indicator of switch posi- tion, the Peak LED indicating circuit remains fully operational by illuminating at a much higher intensity than its use as a PFL status indicator.

PEAK LED Indicator

Illuminates RED when any of the points monitored come with- in 3db of the clipping point. Signal is sampled after the input preamplifier stage, after the EQ section, and after the fader.

This LED also serves as a PFL ON indicator, but at a much lower intensity than when it is used to indicate clipping.

SIGNAL PRESENT LED

Constantly displays level activity of the input channel by vary- ing in intensity.

100mm Fader

Used for control of all outputs of the channel except those Aux output sections selected by switch to a pre fader position. (The Insert Output level is not affected by the fader position.)

DIR OUT

INSERT

BAL LINE IN

BALMIC IN

Rear Connections

Direct Out

This jack provides the direct output signal (post fader & post mute) from the associat- ed input channel.

Insert

This jack allows for the insertion of an effect or signal processor into the audio path of the associated input channel.

Bal Line In

This jack accepts balanced and unbalanced line level inputs and delivers it into the associated input channel.

Bal Mic In

This connector accepts balanced micro- phone inputs for the associated input chan- nel.

PAGE 11

Image 13
Contents SP TC GT Crest Audio Inc Table of Contents Feature Overview Input XLR Output XLR Wiring ConventionsCentury Series Console Power Supply To Console Power ConnectionsSystem Connections Signal Processors SP Input Module Rear Connections TC Input Module Polarity Reverse SwitchHF Equalizer Control MID EQ Level and Sweep ControlsPAN Control PEAK/SHELVE LF Switch PEAK/SHELVE HF SwitchGT Input Module Four-Band Sweep Equalizer ControlsScene Mute Safe Switch Aux 8 Direct SwitchScene Mute Assignments Stereo Switch XLR PAD SwitchGT Stereo Input Module Gain & R Gain ControlsWidth Control PEAK/PFL LED IndicatorBAL Control Group SP/TC Group Modules Matrix Levels A, B GT Group ModuleEffect Aux Sends Group XLR EFX Return Scene Mute Safe SwitchMatrix Pre/Post Fader Reverse w/LEDMatrix Matrix AUX Mains Mono Matrix Module Talk Back SP/TC Master Section Monitor GT Master Section GT Master Section contd GT TC SP Configurations General Specifications SP ConsoleArchitect’s & Engineer’s Specifications SP Console TC Consoles are available in the following configurations GT Consoles are available in the following configurations GT/TC Side Dimensions GT rear view shown Rear Views & DimensionsSP/TC/GT USER-OPTIONS ONE Open the armrest Console DisassemblyTWO Remove top module screw Three Remove rear screwsPage SP TC GT Auxiliary 34 Switch 100mm Fader See Fader 48 Volt Phantom PowerAuxiliary 8 Direct Switch Auxiliary Mute SwitchesGroup XLR Switch Fader Reverse SwitchHF Peak/Shelve Switch High Pass SwitchMatrix Pre/Post Switch LF Peak/Shelve SwitchSwitch Mute SwitchPolarity Reverse Switch Pre/Post Fader Switch Phantom PowerScene Mute Assignment Switch Scene Mute Safe Switch w/LEDSP / TC / GT Appendix C Schematics Crest Audio Inc