Peavey GT owner manual SP/TC Group Modules

Page 19

CENTURY SERIES

SP / TC / GT

SP/TC Group Modules

Since there are only minor differences between the SP and TC input modules, these two models share the same group module. An eight bus console will have eight of these modules where a four bus console will only have four. The number of the group is indicated on the PFL switch.

Group Peak & Signal LED’s

The red LED indicates that the group signal is within 3dB of the clipping point. The green LED constantly displays the level of signal activity by varying in intensity.

Group Fader

Controls the final output signal of the group.

Group Meter

Monitors the post-fader output of the group via a ten-segment LED array.

Effect Return Gain

Controls the gain on the signal returning from an attached effect.

Effect Return EQ

Alters the effect return signal pre-fader via two fixed-frequen- cy (10kHz and 80 Hz) controls.

Effect Return Assignments

Assign the post-pan, post fader, effect return signal to the mix bus.

Effect Aux Levels

Controls the level of effect return signal sent to Auxes 1-4.

Aux 3•4 Switch

Switches the Effect Aux Levels between 1•2 and 3•4.

Pre/Post Switch

Selects the effect return signal between pre and post Effect Level Control, for use with Aux's.

Effect Pan

Adjust the proportion of effect return signal being sent to the Left (odd) and Right (even) mix buses.

Effect Level

Adjusts the final effect return signal level.

Effect Mute

Mutes the effect return signal.

Effect PFL

Allows for Pre Fader Listening of the effect return signal.

Effect Peak & Signal LED’s

The red LED indicates that the effect signal is within 3dB of the clipping point. The green LED constantly displays the level of signal activity by varying in intensity.

Group Pan

Used to position group image between the Left and Right out- put assignments

Group Mute

Mutes the group signal, except for the group insert send.

Group Assignments

Assigns the group signal to the Left, Right, and/or Mono out- puts.

Group PFL

Allows for Pre Fader Listening of the group signal

GROUP OUT

GROUP INSERT

EFX RETURN

Rear Connections

Group Out

This connector carries the post-fader output signal from the associated group module.

Group Insert

This jack allows for the insertion of an effect or signal processor into the audio path of the associated group.

EFX Return

These two connectors allow for effect signals to be brought back into the board. The 1/4" TRS jack accepts a balanced or unbalanced signal at -10 dB level and delivers the signal to the EFX return section. The female XLR connector accepts a balanced signal at +4dB level and delivers the signal to the EFX return section of the group.

PAGE 17

Image 19
Contents SP TC GT Crest Audio Inc Table of Contents Feature Overview Input XLR Output XLR Wiring ConventionsCentury Series Console Power Supply To Console Power ConnectionsSystem Connections Signal Processors SP Input Module Rear Connections MID EQ Level and Sweep Controls Polarity Reverse SwitchTC Input Module HF Equalizer ControlPAN Control Four-Band Sweep Equalizer Controls PEAK/SHELVE HF SwitchPEAK/SHELVE LF Switch GT Input ModuleScene Mute Safe Switch Aux 8 Direct SwitchScene Mute Assignments Gain & R Gain Controls XLR PAD SwitchStereo Switch GT Stereo Input ModuleWidth Control PEAK/PFL LED IndicatorBAL Control Group SP/TC Group Modules Matrix Levels A, B GT Group ModuleEffect Aux Sends Fader Reverse w/LED EFX Return Scene Mute Safe SwitchGroup XLR Matrix Pre/PostMatrix Matrix AUX Mains Mono Matrix Module Talk Back SP/TC Master Section Monitor GT Master Section GT Master Section contd GT TC SP Configurations General Specifications SP ConsoleArchitect’s & Engineer’s Specifications SP Console TC Consoles are available in the following configurations GT Consoles are available in the following configurations GT/TC Side Dimensions GT rear view shown Rear Views & DimensionsSP/TC/GT USER-OPTIONS Three Remove rear screws Console DisassemblyONE Open the armrest TWO Remove top module screwPage SP TC GT Auxiliary Mute Switches 100mm Fader See Fader 48 Volt Phantom PowerAuxiliary 34 Switch Auxiliary 8 Direct SwitchHigh Pass Switch Fader Reverse SwitchGroup XLR Switch HF Peak/Shelve SwitchMute Switch LF Peak/Shelve SwitchMatrix Pre/Post Switch SwitchScene Mute Safe Switch w/LED Phantom PowerPolarity Reverse Switch Pre/Post Fader Switch Scene Mute Assignment SwitchSP / TC / GT Appendix C Schematics Crest Audio Inc