SUPER MICRO Computer SBA-7222G-T2 user manual Initialization before the Coprocessor test next

Page 70

SBA-7222G-T2 Blade Module User’s Manual

 

Notes

 

Table A-4. Uncompressed Initialization Error Codes

 

 

Post Code

Description

95h

Initializing the bus option ROMs from C800 next. See the last page of this

chapter for additional information.

 

96h

Initializing before passing control to the adaptor ROM at C800.

 

 

97h

Initialization before the C800 adaptor ROM gains control has completed.

The adaptor ROM check is next.

 

 

The adaptor ROM had control and has now returned control to BIOS

98h

POST. Performing any required processing after the option ROM

 

returned control.

 

 

99h

Any initialization required after the option ROM test has completed.

Configuring the timer data area and printer base address next.

 

9Ah

Set the timer and printer base addresses. Setting the RS-232 base

address next.

 

 

 

9Bh

Returned after setting the RS-232 base address. Performing any required

initialization before the Coprocessor test next.

 

9Ch

Required initialization before the Coprocessor test is over. Initializing the

Coprocessor next.

 

 

 

9Dh

Coprocessor initialized. Performing any required initialization after the

Coprocessor test next.

 

 

Initialization after the Coprocessor test is complete. Checking the

9Eh

extended keyboard, keyboard ID, and Num Lock key next. Issuing the

 

keyboard ID command next.

 

 

A2h

Displaying any soft errors next.

A3h

The soft error display has completed. Setting the keyboard typematic rate

next.

 

 

 

A4h

The keyboard typematic rate is set. Programming the memory wait states

next.

 

A5h

Memory wait state programming is over. Clearing the screen and

enabling parity and the NMI next.

 

 

 

A7h

NMI and parity enabled. Performing any initialization required before

passing control to the adaptor ROM at E000 next.

 

A8h

Initialization before passing control to the adaptor ROM at E000h

completed. Passing control to the adaptor ROM at E000h next.

 

 

 

A9h

Returned from adaptor ROM at E000h control. Performing any

initialization required after the E000 option ROM had control next.

 

Aah

Initialization after E000 option ROM control has completed. Displaying the

system configuration next.

 

 

 

Abh

Uncompressing the DMI data and executing DMI POST initialization next.

B0h

The system configuration is displayed.

 

 

A-10

Image 70
Contents SBA-7222G-T2 Blade Module User’s Manual SBA-7222G-T2 Blade Module User’s Manual About this Manual PrefaceManual Organization SBA-7222G-T2 Blade Module User’s Manual Table of Contents Blade Module Features Vii Viii List of Figures Full Rack of Blade Enclosures and Blade ServersSBI-7226T-T2 Blade Module User’s Manual List of Tables Xii Chapter Introduction Product Checklist of Typical ComponentsOverview Processors SBA-7222G-T2 Blade Specification FeaturesMemory Storage DensityFull Rack of Blade Enclosures and Blade Servers Europe Contacting SupermicroHeadquarters Asia-PacificSBA-7222G-T2 Blade Module User’s Manual Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions Electrostatic Discharge PrecautionsOperating Precautions SBA-7222G-T2 Blade Module User’s Manual Powering Up a Blade Unit Chapter Setup and InstallationInstalling Blade Modules Powering Down a Blade UnitInstalling a Blade Unit into the Enclosure Removing/Replacing the Blade CoverInserting a Blade into the Enclosure Processor Installation Removing a ProcessorOnboard Battery Installation Installing a G34 Processor in a SocketPopulating Memory Slots Memory InstallationChannel Channel3 Channel4 Slot Dimm Numbering for Two Node Blade Modules Dimm Installation Installing a Dimm into a Memory SlotInstalling a Hard Drive Hard Disk Drive InstallationRemoving a Hard Drive Carrier Installing a Hard Drive in a Carrier Installing with an External USB CD-ROM Drive Installing the Operating SystemInstalling via PXE Boot Linux Installation with Two Hard Drives Configuring and Setting up RAIDInstalling via Virtual Media Drive Redirection Management SoftwareSBA-7222G-T2 Blade Unit Features Chapter Blade Module FeaturesFeature Description Control Panel Blade Control Panel Function State DescriptionKVM Connector Power ButtonLED Indicators KVM ButtonMainboard Bhdgt MainboardBhdgt Mainboard Layout Description Jumpers Cmos ClearBlade Unit Components Exploded View of SBA-7222G-T2 Blade ModuleHard Disk Drives Memory SupportMain Components of SBA-7222G-T2 Blade Unit Bios Setup Chapter RAID Setup ProcedureImportant Notes Setting up the Bios for RAID RAID Setup Procedure Screen Message Chapter Main Bios Setup MenuRunning Setup IntroductionAdvanced Settings Menu System Time/System DateBoot Feature Submenu Boot FeatureMenu Option Description Processor & Clock Options Submenu Processor & Clock OptionsAdvanced Chipset Control Advanced Chipset Control Submenu ECC IDE Configuration IDE Configuration SubmenuPCI/PnP Configuration PCI/PnP Configuration SubmenuSuper IO Configuration Submenu Super IO Device ConfigurationRemote Access Configuration Remote Access Configuration SubmenuAcpi Configuration Hardware Health ConfigurationAcpi Configuration Submenu Ipmi Configuration 10. Ipmi Configuration SubmenuSecurity Menu Event Log Configuration11. Event Log Configuration Submenu 12. Security MenuBoot Menu 13. Boot MenuExit Menu 13. Boot Menu Menu Option Description14. Exit Menu SBA-7222G-T2 Blade Module User’s Manual Bios Post Messages Appendix a Bios Post CodesTable A-1. Bios Post Messages Bios Message CPU ID Table A-1. Bios Post Messages Bios Message Terminal Post Errors Bios Post CodesRecoverable Post Errors Table A-2. Uncompressed Initialization Error CodesBootblock Recovery Codes Table A-3. Bootblock Recovery Error CodesTable A-4. Uncompressed Initialization Error Codes Alternate display memory read/write test next Memory wraparound at 00 next Stuck keys. Issuing the keyboard reset command next Initialization before the Coprocessor test next Table A-4. Uncompressed Initialization Error Codes SBA-7222G-T2 Blade Module User’s Manual Disclaimer SBA-7222G-T2 Blade Module User’s Manual