SUPER MICRO Computer SBA-7222G-T2 Dimm Installation, Installing a Dimm into a Memory Slot

Page 30

SBA-7222G-T2 Blade Module User’s Manual

DIMM Installation

WARNING: Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.

Installing DIMM Memory Modules

1.Power down the blade module (see "Powering Down a Blade Unit" on page 3-1).

2.Remove the blade from the enclosure and the cover from the blade (see "Removing/Replacing the Blade Cover" on page 3-2).

3.Insert each DIMM vertically into its slot. Pay attention to the notch along the bottom of the module to prevent inserting the DIMM incorrectly (see Figure 3-6).

Figure 3-6. Installing a DIMM into a Memory Slot

To Install: Insert module vertically and press down until it snaps into place. Pay attention to the bottom notch.

To Remove: Use your thumbs to gently push each release tab outward to free the DIMM from the slot.

4.Gently press down on the DIMM until it snaps into place in the slot. Repeat for all modules (see Table 3-1for installing DIMMs into the slots in the correct order).

5.Replace the air shroud and the blade cover and install the blade module back into the enclosure.

6.Power up the blade unit (see "Powering Up a Blade Unit" on page 3-1).

3-8

Image 30
Contents SBA-7222G-T2 Blade Module User’s Manual SBA-7222G-T2 Blade Module User’s Manual Preface About this ManualManual Organization SBA-7222G-T2 Blade Module User’s Manual Table of Contents Blade Module Features Vii Viii List of Figures Full Rack of Blade Enclosures and Blade ServersSBI-7226T-T2 Blade Module User’s Manual List of Tables Xii Product Checklist of Typical Components Chapter IntroductionOverview SBA-7222G-T2 Blade Specification Features ProcessorsMemory Storage DensityFull Rack of Blade Enclosures and Blade Servers Europe Contacting SupermicroHeadquarters Asia-PacificSBA-7222G-T2 Blade Module User’s Manual Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions Electrostatic Discharge PrecautionsOperating Precautions SBA-7222G-T2 Blade Module User’s Manual Powering Up a Blade Unit Chapter Setup and InstallationInstalling Blade Modules Powering Down a Blade UnitInstalling a Blade Unit into the Enclosure Removing/Replacing the Blade CoverInserting a Blade into the Enclosure Processor Installation Removing a ProcessorOnboard Battery Installation Installing a G34 Processor in a SocketMemory Installation Populating Memory SlotsChannel Channel3 Channel4 Slot Dimm Numbering for Two Node Blade Modules Dimm Installation Installing a Dimm into a Memory SlotHard Disk Drive Installation Installing a Hard DriveRemoving a Hard Drive Carrier Installing a Hard Drive in a Carrier Installing the Operating System Installing with an External USB CD-ROM DriveInstalling via PXE Boot Linux Installation with Two Hard Drives Configuring and Setting up RAIDInstalling via Virtual Media Drive Redirection Management SoftwareChapter Blade Module Features SBA-7222G-T2 Blade Unit FeaturesFeature Description Control Panel Blade Control Panel Function State DescriptionKVM Connector Power ButtonLED Indicators KVM ButtonMainboard Bhdgt MainboardBhdgt Mainboard Layout Description Jumpers Cmos ClearBlade Unit Components Exploded View of SBA-7222G-T2 Blade ModuleMemory Support Hard Disk DrivesMain Components of SBA-7222G-T2 Blade Unit Chapter RAID Setup Procedure Bios SetupImportant Notes Setting up the Bios for RAID RAID Setup Procedure Screen Message Chapter Main Bios Setup MenuRunning Setup IntroductionAdvanced Settings Menu System Time/System DateBoot Feature Boot Feature SubmenuMenu Option Description Processor & Clock Options Submenu Processor & Clock OptionsAdvanced Chipset Control Advanced Chipset Control Submenu ECC IDE Configuration IDE Configuration SubmenuPCI/PnP Configuration PCI/PnP Configuration SubmenuSuper IO Configuration Submenu Super IO Device ConfigurationRemote Access Configuration Remote Access Configuration SubmenuHardware Health Configuration Acpi ConfigurationAcpi Configuration Submenu Ipmi Configuration 10. Ipmi Configuration SubmenuSecurity Menu Event Log Configuration11. Event Log Configuration Submenu 12. Security MenuBoot Menu 13. Boot Menu13. Boot Menu Menu Option Description Exit Menu14. Exit Menu SBA-7222G-T2 Blade Module User’s Manual Appendix a Bios Post Codes Bios Post MessagesTable A-1. Bios Post Messages Bios Message CPU ID Table A-1. Bios Post Messages Bios Message Terminal Post Errors Bios Post CodesRecoverable Post Errors Table A-2. Uncompressed Initialization Error CodesBootblock Recovery Codes Table A-3. Bootblock Recovery Error CodesTable A-4. Uncompressed Initialization Error Codes Alternate display memory read/write test next Memory wraparound at 00 next Stuck keys. Issuing the keyboard reset command next Initialization before the Coprocessor test next Table A-4. Uncompressed Initialization Error Codes SBA-7222G-T2 Blade Module User’s Manual Disclaimer SBA-7222G-T2 Blade Module User’s Manual