SUPER MICRO Computer 1012G-MTF Checking the Motherboard Setup, Accessing the Inside of the System

Page 24

A+ SERVER 1012G-MTF USER'S MANUAL

2-6 Checking the Motherboard Setup

After you install the 1012G-MTF in the rack, you will need to open the unit to make sure the motherboard is properly installed and all the connections have been made.

Accessing the Inside of the System

1.Grasp the two handles on either side and pull the unit straight out until it locks (you will hear a "click").

2.Depress the two buttons on the top of the chassis to release the top cover. There is a large rectangular recess in the middle front of the top cover to help you push the cover away from you until it stops.

3.Lift the top cover from the chassis to gain full access to the inside of the server. See Figure 2-4 for a view.

Figure 2-4. Typical Server with Top Cover Open

2-8

Image 24
Contents Super Page Preface About This ManualManual Organization Advanced Chassis Setup BiosPreface Contents System Interface Viii Advanced Chassis Setup Bios Chapter Introduction OverviewMotherboard Features Processors MemorySerial ATA PCI Expansion SlotsServer Chassis Features AMD SR5650/SP5100 Chipset System Block Diagram Cooling SystemContacting Supermicro HeadquartersEurope Asia-PacificPage Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Rear Inner RailsIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing Rear Inner Chassis RailsInstalling the Server into the Rack Installing the Server into a Telco Rack Checking the Motherboard Setup Accessing the Inside of the SystemChecking the Drive Bay Setup Providing PowerChecking the Components Checking the AirflowPage Reset PowerChapter System Interface Control Panel ButtonsControl Panel LEDs Information LEDInformation LED Status DescriptionDrive Carrier LEDs HDDPage Chapter Standardized Warning Statements for AC Systems About Standardized Warning Statementsהרהזא תורהצה ןונקת Bewaar Deze Instructies Installation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。Circuit Breaker Power Disconnection Warning 電源切断の警告םיביכר תרסה וא תנקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפל Equipment Installation 機器の設置Restricted Area アクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。Battery Handling 電池の取り扱いPage Redundant Power Supplies הדיחיה תאBackplane Voltage バックプレーンの電圧Comply with Local and National Electrical Codes 地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。Product Disposal 製品の廃棄Hot Swap Fan Warning ファン・ホットスワップの警告當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Power Cable and AC Adapter 電源コードとACアダプターPage Page Chapter Advanced Motherboard Setup PrecautionsHandling the Motherboard UnpackingMotherboard Installation Connecting CablesConnecting Data Cables Installing to the MotherboardConnecting Power Cables Connecting the Control PanelI/O Ports I/O PortsProcessor and Heatsink Installation Installing the ProcessorsCPU and/or the socket Installing a Passive CPU Heatsink SNK-0042P HeatsinkInstalling Memory Installing MemoryMemory Support Release Tab Front ViewMaximum Memory Per Channel Dimm Populations OptionsInstalling an Expansion Card Adding PCI Expansion CardsPossible System Memory Allocation & Availability Motherboard Details H8SGL-F Motherboard LayoutJumper Description Default Setting H8SGL-F Quick ReferenceAdvanced Motherboard Setup Connector Definitions Power ConnectorsPwon Connector Reset ConnectorPower On LED Video ConnectorNMI Button Universal Serial Bus Ports USB HeadersFan Headers Serial PortsPower I2C Chassis IntrusionOverheat LED Wake-On-LANPower LED/Speaker ATX PS/2 Keyboard and PS/2 Mouse PortsCompact Flash Card PWR Connector Trusted Platform Module HeaderLAN1/2 Ethernet Ports Jumper Settings Explanation of JumpersCmos Clear To Clear CmosVGA Enable/Disable LAN1/2 Enable/DisableOnboard Speaker Enable/Disable I2C to PCI-Express SlotWatch Dog Enable/Disable Compact Flash Master/Slave SelectUSB Wake-Up BMC JumperOnboard Indicators Power LEDLAN1/LAN2 LEDs Dedicated Ipmi LAN LEDsIDE Connector IDE and Sata Drive ConnectionsSata Ports Installing the OS/SATA Driver Enabling Sata RAIDSerial ATA Sata Building a Driver DisketteEnabling Sata RAID in the Bios Bios Setup ScreenUsing the DotHill and Adaptec RAID Utility DotHill RAID Utility Program ScreenInstalling Software Installing the RAID Driver During OS InstallationDriver/Tool Installation Display Screen SuperDoctor11. SuperDoctor III Interface Display Screen Remote Control Motherboard Battery 12. Installing the Onboard BatteryPage Chapter Advanced Chassis Setup Static-Sensitive DevicesControl Panel USB COM1 VGA Ethernet Ports Port Port PortsDrive Bay Installation/Removal System FansRemoving the Front Bezel System Fan FailureAccessing the Drive Bays Sata Drive InstallationMounting a Drive in a Drive Carrier Installing/Removing SAS/SATA Drives Sata BackplaneDVD-ROM Drive Installation Removing/Installing a DriveRemoving the Chassis Cover Power Supply Power Supply FailureReplacing the Power Supply Page Starting the Setup Utility ChapterIntroduction Advanced Settings Menu  Boot FeatureMain Menu Wait for F1 if Error Power Button FunctionRestore on AC Power Loss Hit DEL Message Display Processor and Clock Options  Advanced Chipset Control  NorthBridge Configuration  Memory Configuration ECC Configuration  IDE Configuration  Dram Timing Configuration Primary/Secondary/Third/Fourth IDE Master/Slave  PCI/PnP Configuration  SuperIO Device Configuration  Remote Access Configuration  Hardware Health Configuration Sredir Memory Display DelayCPU Overheat Alarm VT-UTF8 Combo Key Support Acpi Configuration PS2 KB/MS Wakeup Ipmi Configuration  Set LAN Configuration View BMC System Event Log BMC Watch Dog Timer Action IP Address SourceIP Address Subnet Mask Event Log Configuration Security MenuBoot Menu  Boot Device PriorityRetry Boot Devices  Hard Disk DrivesExit Menu Page Appendix a Post Error Beep Codes Amibios Error Beep CodesPage Appendix B System Specifications Weight Power SupplyChassis System CoolingRegulatory Compliance