SUPER MICRO Computer 5015A-EHF-D525 user manual Motherboard Installation, Unpacking

Page 34

SUPERSERVER 5015A-EHF-D525 User's Manual

Unpacking

The motherboard is shipped in antistatic packaging to avoid electrical static dis- charge. When unpacking the board, make sure the person handling it is static protected.

5-2 Motherboard Installation

This section explains the first step of physically mounting the X7SPE-HF-D525 into the SC502L-200B chassis. Following the steps in the order given will eliminate the most common problems encountered in such an installation. To remove the moth- erboard, follow the procedure in reverse order.

Installing to the Chassis

1.Access the inside of the system by removing the screws from the top cover of the chassis, then lift the cover off.

2.Make sure that the I/O ports on the motherboard align properly with their respective holes in the I/O shield at the back of the chassis.

3.Carefully mount the motherboard to the motherboard tray by aligning the board holes with the raised metal standoffs that are visible in the chassis.

4.Insert screws into all the mounting holes on your motherboard that line up with the standoffs and tighten until snug (if you screw them in too tight, you might strip the threads). Metal screws provide an electrical contact to the motherboard ground to provide a continuous ground for the system.

5.Finish by replacing the top cover of the chassis.

Warning: To avoid damaging the motherboard and its components, do not apply any force greater than 8 lbs. per square inch when installing a screw into a mount- ing hole.

5-2

Image 34
Contents Super Manual Revision Release Date October 18 Manual Organization Server InstallationAbout This Manual IntroductionAdvanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Chassis Setup Table of Contents Page Chapter Introduction OverviewMotherboard Features Intel Atom D525 + ICH9R Chipset System Block Diagram Server Chassis Features Europe Contacting SupermicroHeadquarters Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the Chassis into a Rack Rack Mounting InstructionsInstalling into a Telco Rack Installing the Chassis into a Telco RackAccessing the Inside of the System Figure Checking the Motherboard SetupChecking the Components Accessing the Inside of the System Providing Power Checking the Drive Bay SetupChecking the Drives Control Panel Buttons Reset ButtonPower Control Panel LEDsOverheat HDDPower Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Handling the MotherboardInstalling to the Chassis Motherboard InstallationUnpacking Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins I/O PortsOnboard Processor Installing MemoryDimm Installation Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsMotherboard Details Number Connector Description JPCIE1External Power Connector Connector DefinitionsMain ATX Power Supply Connector Power ButtonPower Fail LED Reset ButtonOverheat/Fan Fail Fan Headers Power LEDNMI Button Overheat/Fan Fail LED JOHChassis Intrusion Sata DOM PowerPower SMB I2C Connector Serial PortsSgpio 0/1 Headers ATX PS/2 Keyboard and PS/2 Mouse PortsLAN1/2 Ethernet Ports Universal Serial Bus USB Trusted Platform Module HeaderExplanation of Jumpers Jumper SettingsLAN1/2 Enable/Disable Cmos ClearVGA Enable/Disable Watch Dog Enable/DisablePower Force On Enable/Disable SMB I2C Bus to PCI SlotsDCD / P5V Select OEM option BMC Enable/DisableCOM3 Redirection Select OEM option LAN1/2 LEDs Onboard IndicatorsSata Ports Sata PortsInstalling Software Supero Doctor Supero Doctor III Interface Display Screen Remote Control Page Control Panel Chassis Front ViewInstallling 2.5 Sata Drives Figure Drive Bay Installation/RemovalInstallling a 3.5 Sata Drive Figure System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSystem Memory Quick Boot Advanced Setup ConfigurationsXboot Feature Quiet BootPower Button Function Bootup Num-LockWait For F1 If Error Restore on AC Power LossClock Spread Spectrum Standby Power in S5Xcpu Configuration Max Cpuid Value LimitXAdvanced Chipset Control XNorthbridge ConfigurationXIDE/SATA Configuration PIO Mode IDE Detect Timeout secLBA/Large Mode TypeDMA Mode XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationFlow Control Redirection After Bios PostSredir Memory Display Delay Terminal TypeSystem Temperature CPU Overheat AlarmCPU Temperature XHardware Health ConfigurationCpufan / Sysfan Speed Fan Speed Control Modes High Performance Event TimerXacpi Configuration USB Device WakeupAcpi Version Features Suspend ModeHeadless Mode Acpi Aware O/SXipmi Configuration XEvent Log Configuration User Password Security SettingsSupervisor Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionXBoot Device Priority Boot SettingsXHard Disk Drives XRemovable Drives Retry Boot DevicesExit Options Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications

5015A-EHF-D525 specifications

The Super Micro Computer 5015A-EHF-D525 is an exceptional server designed to deliver outstanding performance in various computing environments. It is a robust solution tailored for small to medium-sized businesses, offering a perfect balance of power and efficiency.

At the heart of the 5015A-EHF-D525 is the Intel Atom D525 processor, a dual-core CPU that operates with a thermal design power of just 13 watts. This low-power design not only contributes to energy savings but also results in less heat generation, allowing the server to operate quietly, making it ideal for environments where noise is a concern.

One of the standout features of the 5015A-EHF-D525 is its compact form factor. The server's efficient design fits perfectly in a 1U rackmount space, providing a high-density solution without compromising on performance. This compact design is especially beneficial for businesses looking to optimize space in their data centers.

The server supports up to 8GB of DDR3 memory, offering ample capacity to handle various workloads and applications efficiently. With two DIMM slots available, users can easily upgrade their memory as their needs grow. This flexibility ensures that the server can adapt to evolving business requirements.

In terms of storage, the Super Micro 5015A-EHF-D525 offers a range of options. It includes support for up to four 3.5-inch SATA drives, allowing for significant storage capacity to accommodate data-intensive applications. With support for RAID 0, 1, 5, and 10 configurations, users can enhance data protection and improve performance.

Connectivity is another strong point of the 5015A-EHF-D525. The server features dual Gigabit Ethernet ports, enabling high-speed network access and redundancy. This dual-port configuration ensures that the system remains operational even in the event of a network failure.

The server is equipped with IPMI 2.0 support, which allows for remote management and monitoring. This technology provides administrators with the ability to manage the server even when the operating system is not functional, ensuring maximum uptime and efficiency.

Super Micro has integrated various energy-efficient technologies into the 5015A-EHF-D525, making it compliant with various green computing initiatives. This commitment to sustainability is reflected in its design and operation, allowing businesses to minimize their environmental impact while maximizing performance.

In conclusion, the Super Micro Computer 5015A-EHF-D525 is a powerful, efficient, and versatile server perfect for businesses seeking a reliable computing solution. Its combination of advanced features, low power consumption, and excellent expandability makes it a formidable choice in the competitive server market.