SUPER MICRO Computer 5015A-EHF-D525 user manual DCD / P5V Select OEM option, BMC Enable/Disable

Page 50

SUPERSERVER 5015A-EHF-D525 User's Manual

DCD / P5V Select (OEM option)

Jumpers J10~J13 allow selection between the standard Data Carrier Detect (DCD) modem signal or the system voltage +5V on pin 1 of the COM1~COM4 ports This is an OEM option only.

COM3 Redirection Select (OEM option)

JPC3 allows selection between RS232 or TTL for COM3 redirection. The de- fault setting is RS232. This is an OEM option only.

BMC Enable/Disable

The JPB jumper is used to enable or disable the onboard Baseboard Man- agement Controller (BMC) and IPMI. This jumper is used together with the IPMI settings in the BIOS. The default position is pins 1 and 2 to Enable BMC. See the table on the right for jumper settings.

DCD / P5V Select

Jumper Settings

Jumper Setting

 

Definition

Pins 1-2

 

DCD

 

Pins 2-3

 

P5V

 

 

 

 

COM3 Redirection Select

Jumper Settings

Jumper Setting

 

Definition

Pins 1-2

 

RS232

 

 

 

(default)

Pins 2-3

 

TTL

 

Open

 

Disabled

 

 

 

 

 

BMC

Jumper Settings

 

 

 

Pin Setting

 

Definition

Pins 1-2

 

Enabled

 

Pins 2-3

 

Disabled

 

 

 

 

5-18

Image 50
Contents Super Manual Revision Release Date October 18 Manual Organization Server InstallationAbout This Manual IntroductionAdvanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Chassis Setup Table of Contents Page Chapter Introduction OverviewMotherboard Features Intel Atom D525 + ICH9R Chipset System Block Diagram Server Chassis Features Europe Contacting SupermicroHeadquarters Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the Chassis into a Rack Rack Mounting InstructionsInstalling into a Telco Rack Installing the Chassis into a Telco RackChecking the Components Checking the Motherboard SetupAccessing the Inside of the System Figure Accessing the Inside of the System Checking the Drives Checking the Drive Bay SetupProviding Power Control Panel Buttons Reset ButtonPower Control Panel LEDsOverheat HDDPower Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Handling the MotherboardUnpacking Motherboard InstallationInstalling to the Chassis Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins I/O PortsOnboard Processor Installing MemoryDimm Installation Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsMotherboard Details Number Connector Description JPCIE1External Power Connector Connector DefinitionsMain ATX Power Supply Connector Power ButtonOverheat/Fan Fail Reset ButtonPower Fail LED Fan Headers Power LEDNMI Button Overheat/Fan Fail LED JOHChassis Intrusion Sata DOM PowerPower SMB I2C Connector Serial PortsLAN1/2 Ethernet Ports ATX PS/2 Keyboard and PS/2 Mouse PortsSgpio 0/1 Headers Universal Serial Bus USB Trusted Platform Module HeaderExplanation of Jumpers Jumper SettingsLAN1/2 Enable/Disable Cmos ClearVGA Enable/Disable Watch Dog Enable/DisablePower Force On Enable/Disable SMB I2C Bus to PCI SlotsCOM3 Redirection Select OEM option BMC Enable/DisableDCD / P5V Select OEM option LAN1/2 LEDs Onboard IndicatorsSata Ports Sata PortsInstalling Software Supero Doctor Supero Doctor III Interface Display Screen Remote Control Page Control Panel Chassis Front ViewInstallling 2.5 Sata Drives Figure Drive Bay Installation/RemovalInstallling a 3.5 Sata Drive Figure System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilitySystem Memory System Time/System DateProcessor Quick Boot Advanced Setup ConfigurationsXboot Feature Quiet BootPower Button Function Bootup Num-LockWait For F1 If Error Restore on AC Power LossClock Spread Spectrum Standby Power in S5Xcpu Configuration Max Cpuid Value LimitXAdvanced Chipset Control XNorthbridge ConfigurationXIDE/SATA Configuration PIO Mode IDE Detect Timeout secLBA/Large Mode TypeDMA Mode XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationFlow Control Redirection After Bios PostSredir Memory Display Delay Terminal TypeSystem Temperature CPU Overheat AlarmCPU Temperature XHardware Health ConfigurationCpufan / Sysfan Speed Fan Speed Control Modes High Performance Event TimerXacpi Configuration USB Device WakeupAcpi Version Features Suspend ModeHeadless Mode Acpi Aware O/SXipmi Configuration XEvent Log Configuration User Password Security SettingsSupervisor Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionXHard Disk Drives Boot SettingsXBoot Device Priority XRemovable Drives Retry Boot DevicesExit Options Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications

5015A-EHF-D525 specifications

The Super Micro Computer 5015A-EHF-D525 is an exceptional server designed to deliver outstanding performance in various computing environments. It is a robust solution tailored for small to medium-sized businesses, offering a perfect balance of power and efficiency.

At the heart of the 5015A-EHF-D525 is the Intel Atom D525 processor, a dual-core CPU that operates with a thermal design power of just 13 watts. This low-power design not only contributes to energy savings but also results in less heat generation, allowing the server to operate quietly, making it ideal for environments where noise is a concern.

One of the standout features of the 5015A-EHF-D525 is its compact form factor. The server's efficient design fits perfectly in a 1U rackmount space, providing a high-density solution without compromising on performance. This compact design is especially beneficial for businesses looking to optimize space in their data centers.

The server supports up to 8GB of DDR3 memory, offering ample capacity to handle various workloads and applications efficiently. With two DIMM slots available, users can easily upgrade their memory as their needs grow. This flexibility ensures that the server can adapt to evolving business requirements.

In terms of storage, the Super Micro 5015A-EHF-D525 offers a range of options. It includes support for up to four 3.5-inch SATA drives, allowing for significant storage capacity to accommodate data-intensive applications. With support for RAID 0, 1, 5, and 10 configurations, users can enhance data protection and improve performance.

Connectivity is another strong point of the 5015A-EHF-D525. The server features dual Gigabit Ethernet ports, enabling high-speed network access and redundancy. This dual-port configuration ensures that the system remains operational even in the event of a network failure.

The server is equipped with IPMI 2.0 support, which allows for remote management and monitoring. This technology provides administrators with the ability to manage the server even when the operating system is not functional, ensuring maximum uptime and efficiency.

Super Micro has integrated various energy-efficient technologies into the 5015A-EHF-D525, making it compliant with various green computing initiatives. This commitment to sustainability is reflected in its design and operation, allowing businesses to minimize their environmental impact while maximizing performance.

In conclusion, the Super Micro Computer 5015A-EHF-D525 is a powerful, efficient, and versatile server perfect for businesses seeking a reliable computing solution. Its combination of advanced features, low power consumption, and excellent expandability makes it a formidable choice in the competitive server market.