SUPER MICRO Computer 5015A-EHF-D525 Power LED, NMI Button, Fan Headers, Overheat/Fan Fail LED JOH

Page 44

SUPERSERVER 5015A-EHF-D525 User's Manual

Power LED

The Power LED connector is located on pins 15 and 16 of JF1. This con- nection is used to provide LED indica- tion of power being supplied to the system. See the table on the right for pin definitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions.

Fan Headers

The X7SPE-HF-D525 has two fan headers. Fan1 is the CPU fan and Fan2 is for the system cooling fan. These fans are 4-pin fan headers. However, Pins 1~3 of the fan head- ers are backward compatible with the traditional 3-pin fans. (The speeds of 4-pin (PWM) fans are controlled by Thermal Management via BIOS Hard- ware Monitoring in the Advanced Set- ting. (The default setting is Disabled.) Note: Please use all 3-pin fans or all 4-pin fans on a motherboard. Please do not use 3-pin fans and 4-pin fans on the same board.

Power LED

Pin Definitions (JF1)

Pin# Definition

155V Stby

16Control

NMI Button

Pin Definitions (JF1)

Pin# Definition

1Signal

2Ground

Fan Header

Pin Definitions

Pin# Definition

1Ground

2+12V

3Tachometer

4PWM Control

Overheat/Fan Fail LED (JOH)

The JOH header is used to connect an LED to provide warnings of chas- sis overheat. This LED will also blink to indicate a fan failure. Refer to the table on right for pin definitions.

Overheat LED Pin Definitions

Pin# Definition

15vDC

2OH Active

OH/Fan Fail LED

Status Message

State

 

Message

Solid

 

Overheat

 

Blinking

 

Fan Fail

 

 

 

 

5-12

Image 44
Contents Super Manual Revision Release Date October 18 Server Installation About This ManualManual Organization IntroductionSystem Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Chassis Setup Table of Contents Page Chapter Introduction OverviewMotherboard Features Intel Atom D525 + ICH9R Chipset System Block Diagram Server Chassis Features Contacting Supermicro HeadquartersEurope Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the Chassis into a Rack Rack Mounting InstructionsInstalling into a Telco Rack Installing the Chassis into a Telco RackChecking the Components Checking the Motherboard SetupAccessing the Inside of the System Figure Accessing the Inside of the System Checking the Drives Checking the Drive Bay SetupProviding Power Reset Button PowerControl Panel Buttons Control Panel LEDsOverheat HDDPower Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Handling the MotherboardUnpacking Motherboard InstallationInstalling to the Chassis Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins I/O PortsInstalling Memory Dimm InstallationOnboard Processor Memory SupportDimm Installation Installing an Expansion Card Adding PCI Expansion CardsMotherboard Details Number Connector Description JPCIE1Connector Definitions Main ATX Power Supply ConnectorExternal Power Connector Power ButtonOverheat/Fan Fail Reset ButtonPower Fail LED Power LED NMI ButtonFan Headers Overheat/Fan Fail LED JOHSata DOM Power Power SMB I2C ConnectorChassis Intrusion Serial PortsLAN1/2 Ethernet Ports ATX PS/2 Keyboard and PS/2 Mouse PortsSgpio 0/1 Headers Universal Serial Bus USB Trusted Platform Module HeaderJumper Settings LAN1/2 Enable/DisableExplanation of Jumpers Cmos ClearWatch Dog Enable/Disable Power Force On Enable/DisableVGA Enable/Disable SMB I2C Bus to PCI SlotsCOM3 Redirection Select OEM option BMC Enable/DisableDCD / P5V Select OEM option Onboard Indicators Sata PortsLAN1/2 LEDs Sata PortsInstalling Software Supero Doctor Supero Doctor III Interface Display Screen Remote Control Page Control Panel Chassis Front ViewDrive Bay Installation/Removal Installling a 3.5 Sata Drive FigureInstallling 2.5 Sata Drives Figure System FansInstalling a 3.5 Hard Drive Power Supply Replacing the Power Supply FigureInstalling the Power Supply Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilitySystem Memory System Time/System DateProcessor Advanced Setup Configurations Xboot FeatureQuick Boot Quiet BootBootup Num-Lock Wait For F1 If ErrorPower Button Function Restore on AC Power LossStandby Power in S5 Xcpu ConfigurationClock Spread Spectrum Max Cpuid Value LimitXAdvanced Chipset Control XNorthbridge ConfigurationXIDE/SATA Configuration IDE Detect Timeout sec LBA/Large ModePIO Mode TypeDMA Mode XPCI/PnP Configuration XRemote Access Configuration XSuper IO Device ConfigurationRedirection After Bios Post Sredir Memory Display DelayFlow Control Terminal TypeCPU Overheat Alarm CPU TemperatureSystem Temperature XHardware Health ConfigurationCpufan / Sysfan Speed High Performance Event Timer Xacpi ConfigurationFan Speed Control Modes USB Device WakeupSuspend Mode Headless ModeAcpi Version Features Acpi Aware O/SXipmi Configuration XEvent Log Configuration Security Settings Supervisor PasswordUser Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionXHard Disk Drives Boot SettingsXBoot Device Priority Retry Boot Devices Exit OptionsXRemovable Drives Save Changes and ExitLoad Optimal Defaults Load Fail-Safe DefaultsDiscard Changes and Exit Discard ChangesAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications

5015A-EHF-D525 specifications

The Super Micro Computer 5015A-EHF-D525 is an exceptional server designed to deliver outstanding performance in various computing environments. It is a robust solution tailored for small to medium-sized businesses, offering a perfect balance of power and efficiency.

At the heart of the 5015A-EHF-D525 is the Intel Atom D525 processor, a dual-core CPU that operates with a thermal design power of just 13 watts. This low-power design not only contributes to energy savings but also results in less heat generation, allowing the server to operate quietly, making it ideal for environments where noise is a concern.

One of the standout features of the 5015A-EHF-D525 is its compact form factor. The server's efficient design fits perfectly in a 1U rackmount space, providing a high-density solution without compromising on performance. This compact design is especially beneficial for businesses looking to optimize space in their data centers.

The server supports up to 8GB of DDR3 memory, offering ample capacity to handle various workloads and applications efficiently. With two DIMM slots available, users can easily upgrade their memory as their needs grow. This flexibility ensures that the server can adapt to evolving business requirements.

In terms of storage, the Super Micro 5015A-EHF-D525 offers a range of options. It includes support for up to four 3.5-inch SATA drives, allowing for significant storage capacity to accommodate data-intensive applications. With support for RAID 0, 1, 5, and 10 configurations, users can enhance data protection and improve performance.

Connectivity is another strong point of the 5015A-EHF-D525. The server features dual Gigabit Ethernet ports, enabling high-speed network access and redundancy. This dual-port configuration ensures that the system remains operational even in the event of a network failure.

The server is equipped with IPMI 2.0 support, which allows for remote management and monitoring. This technology provides administrators with the ability to manage the server even when the operating system is not functional, ensuring maximum uptime and efficiency.

Super Micro has integrated various energy-efficient technologies into the 5015A-EHF-D525, making it compliant with various green computing initiatives. This commitment to sustainability is reflected in its design and operation, allowing businesses to minimize their environmental impact while maximizing performance.

In conclusion, the Super Micro Computer 5015A-EHF-D525 is a powerful, efficient, and versatile server perfect for businesses seeking a reliable computing solution. Its combination of advanced features, low power consumption, and excellent expandability makes it a formidable choice in the competitive server market.