SUPER MICRO Computer SBI-7127R-S6 user manual Table A-1. Bios Post Messages Bios Message

Page 75

Appendix A

BIOS POST Codes

A-1 BIOS POST Messages

During the Power-On Self-Test (POST), the BIOS will check for problems. If a problem is found, the BIOS will activate an alarm or display a message. The following is a list of such BIOS messages.

Table A-1. BIOS POST Messages

BIOS Message

Failure Fixed Disk

Stuck key

Keyboard error

Keyboard Controller Failed

Keyboard locked - Unlock key switch

Monitor type does not match CMOS - Run SETUP

Shadow Ram Failed at offset: nnnn

System RAM Failed at offset: nnnn

Extended RAM Failed at offset: nnnn

System battery is dead - Replace and run SETUP

System CMOS checksum bad - Default configuration used

System timer error

Real time clock error

Check date and time settings

Description

Fixed disk is not working or not configured properly. Check to see if fixed disk is attached properly. Run Setup. Find out if the fixed-disk type is correctly identified.

Stuck key on keyboard.

Keyboard not working.

Keyboard controller failed test. May require replacing keyboard controller.

Unlock the system to proceed.

Monitor type not correctly identified in Setup

Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.

System RAM failed at offset nnnn of in the 64k block at which the error was detected.

Extended memory not working or not configured properly at offset nnnn.

The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup to reconfigure the system.

System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in CMOS. The BIOS installed Default Setup Values. If you do not want these values, enter Setup and enter your own values. If the error persists, check the system battery or contact your dealer.

The timer test failed. Requires repair of system board.

Real-Time Clock fails BIOS hardware test. May require board repair.

BIOS found date or time out of range and reset the Real-Time Clock. May require setting legal date (1991-2099).

A-1

Image 75
Contents SBI-7127R-S6 Blade Module User’s Manual SBI-7427R-T3 Blade Module User’s Manual Manual Organization About this ManualSBI-7427R-T3 Blade Module User’s Manual Table of Contents Table of Contents Vii Viii Overview Product Checklist of Typical ComponentsMemory Blade Module FeaturesSBI-7127R-S6 Blade Module Specification Features ProcessorsDensity StorageFull Rack of Blade Enclosures and Blade Servers Asia-Pacific Contacting SupermicroHeadquarters EuropeSBI-7127R-S6 Blade Module User’s Manual These warnings may also be found on our web site at http About Standardized Warning StatementsWarnung הרהזא תורהצה ןונקתInstallation Instructions 設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。¡Advertencia Waarschuwing Circuit Breaker電源切断の警告 Power Disconnection Warning機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Areaדכו לוענמ ,חתפמ דבלב החטבא ילכ תלבגומ השיג םע רוזא電池の取り扱い Battery Handlingדחא קפסמ רתוי םייק םא Redundant Power SuppliesBackplane Voltage ירוחאה לנפב חתמיצראה למשחה יקוח םואית Comply with Local and National Electrical Codes地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 רצומה קוליס Product Disposal製品の廃棄 ファン・ホットスワップの警告 Hot Swap Fan Warning電源コードと AC アダプター Power Cable and AC AdapterAC ימאתמו םיילמשח Standardized Warning Statements SBI-7127R-SH Blade Module User’s Manual Installing Blade Modules Powering Up a Blade UnitPowering Down a Blade Unit Installing a Blade Unit into the Enclosure Removing a Blade Unit from the EnclosureRemoving/Replacing the Blade Cover Inserting a Blade into the Enclosure Removing a Processor Processor InstallationOpen First Load Lever Opening the Load Plate Aligning CPU Keys with Socket Keys Closing the Load Plate Onboard Battery Installation Memory InstallationPopulating Memory Slots 13 -slot Dimm Numbering Channel14. Installing a Dimm into a Memory Slot Dimm InstallationRemoving a Hard Drive Carrier Hard Disk Drive InstallationInstalling with an External USB CD-ROM Drive Installing the Operating SystemInstalling via Virtual Media Drive Redirection Installing via PXE BootManagement Software Configuring and Setting up RAIDSBI-7127R-S6 Blade Module User’s Manual Description SBI-7127R-S6 Blade Unit FeaturesBlade Control Panel Function State Description Control PanelKVM Button Power ButtonLED Indicators KVM ConnectorB9DR7 Mainboard MainboardB9DR7 Mainboard Layout Intel C602J/Intel 602J Chipset Block DiagramCmos Clear JumpersBlade Unit Components Hard Disk Drives Memory SupportIntroduction BiosFlashing Bios Bios UpdatesType flash filename.rom Running SetupMain Bios Setup Main Bios Setup Menu OptionsMenu Option Description Sub-menu Description Advanced SetupAdvanced Setup Menu Options Boot Feature SubmenuCPU Configuration Submenu Menu Option Boot Feature Submenu Menu OptionBios Chipset Configuration Sub-menu Menu Option Sata Configuration Sub-menu Menu Option SuperIO Device Configuration Sub-menu PCIe/PCI/PnP Configuration Sub-menu Menu OptionSerial Port Console Redirection Sub-menu SuperIO Device Configuration Sub-menu Menu OptionCOM2 Serial Port Console Redirection Sub-menu Menu Option11. ME Subsystem Sub-menu Menu Option 10. Acpi Settings Sub-menu Menu Option12. Event Logs Menu Menu Option Event Logs Setup13. Ipmi Menu Menu Option Ipmi Setup15. Security Menu Options Boot14. Boot Setup Menu Options Security16. Exit Menu Options Save & ExitSBI-7127R-S6 Blade Module User’s Manual Table A-1. Bios Post Messages Bios Message Bios Post MessagesSBI-7427R-S3/T3 Blade Module User’s Manual Bios Post Codes Post Code Description Recoverable Post ErrorsTerminal Post Errors Table A-2. Terminal Post ErrorsAppendix a Bios Post Codes SBI-7427R-S3/T3 Blade Module User’s Manual Table A-2. Terminal Post Errors Post Code Table A-3. Boot Block Flash ROM Terminal Post Errors Appendix a Bios Post Codes SBI-7427R-S3/T3 Blade Module User’s Manual Disclaimer SBI-7127R-S6 Blade Module User’s Manual