SUPER MICRO Computer SBI-7127R-S6 user manual Onboard Battery Installation, Memory Installation

Page 41

Chapter 3: Setup and Installation

3-4 Onboard Battery Installation

A battery is included on the mainboard to supply certain volatile memory components with power when power has been removed from the blade module. If this battery dies, it must be replaced with an equivalent CR2032 Lithium 3V battery. Dispose of used batteries according to the manufacturer's instructions. See Figure 3-12for a diagram of installing a new onboard battery.

Caution: There is a danger of explosion if the onboard battery is installed upside down, which reverses its polarities.

Figure 3-12. Installing the Onboard Battery

Lithium Battery

Battery Holder

3-5 Memory Installation

The mainboard of each blade unit must be populated with DIMMs (Dual In-line Memory Modules) to provide system memory. The DIMMs should all be of the same size and speed and from the same Super Micro authorized manufacturer due to compatibility issues. See details below on supported memory and our web site (www.supermicro.com/products/superblade for recommended memory.

Caution: For all SBI-7427R series blades, ONLY VLP (Very low profile) memory can be used.

Populating Memory Slots

The mainboard of a SBI-7127R-S6 blade module has sixteen (16) memory slots, eight for each processor. Both interleaved and non-interleaved memory are supported, so you may populate any number of DIMM slots.

Populating two slots at a time (DIMM1A + DIMM2A, DIMM3A + DIMM4A, etc.) with memory modules of the same size and of the same type will result in dual-channel, interleaved memory, which is faster than single-channel, non-interleaved memory. See Table 3-1: "Populating Eight Memory Slots for Interleaved Operation" on page 3-10for details.

For an interleaved configuration, memory modules of the same size and speed must be installed in pairs. You should not mix DIMMs of different sizes and speeds.

3-9

Image 41
Contents SBI-7127R-S6 Blade Module User’s Manual SBI-7427R-T3 Blade Module User’s Manual Manual Organization About this ManualSBI-7427R-T3 Blade Module User’s Manual Table of Contents Table of Contents Vii Viii Overview Product Checklist of Typical ComponentsSBI-7127R-S6 Blade Module Specification Features Blade Module FeaturesProcessors MemoryDensity StorageFull Rack of Blade Enclosures and Blade Servers Headquarters Contacting SupermicroEurope Asia-PacificSBI-7127R-S6 Blade Module User’s Manual These warnings may also be found on our web site at http About Standardized Warning StatementsWarnung הרהזא תורהצה ןונקת¡Advertencia Installation Instructions設置手順書 システムを電源に接続する前に、設置手順書をお読み下さい。 Waarschuwing Circuit Breaker電源切断の警告 Power Disconnection Warning機器の設置 Equipment Installationアクセス制限区域 このユニットは、アクセス制限区域に設置されることを想定しています。 Restricted Areaדכו לוענמ ,חתפמ דבלב החטבא ילכ תלבגומ השיג םע רוזא電池の取り扱い Battery Handlingדחא קפסמ רתוי םייק םא Redundant Power SuppliesBackplane Voltage ירוחאה לנפב חתמ地方および国の電気規格に準拠 機器の取り付けはその地方および国の電気規格に準拠する必要があります。 יצראה למשחה יקוח םואיתComply with Local and National Electrical Codes 製品の廃棄 רצומה קוליסProduct Disposal ファン・ホットスワップの警告 Hot Swap Fan Warning電源コードと AC アダプター Power Cable and AC AdapterAC ימאתמו םיילמשח Standardized Warning Statements SBI-7127R-SH Blade Module User’s Manual Powering Down a Blade Unit Installing Blade ModulesPowering Up a Blade Unit Removing/Replacing the Blade Cover Installing a Blade Unit into the EnclosureRemoving a Blade Unit from the Enclosure Inserting a Blade into the Enclosure Removing a Processor Processor InstallationOpen First Load Lever Opening the Load Plate Aligning CPU Keys with Socket Keys Closing the Load Plate Populating Memory Slots Onboard Battery InstallationMemory Installation 13 -slot Dimm Numbering Channel14. Installing a Dimm into a Memory Slot Dimm InstallationRemoving a Hard Drive Carrier Hard Disk Drive InstallationInstalling with an External USB CD-ROM Drive Installing the Operating SystemInstalling via Virtual Media Drive Redirection Installing via PXE BootManagement Software Configuring and Setting up RAIDSBI-7127R-S6 Blade Module User’s Manual Description SBI-7127R-S6 Blade Unit FeaturesBlade Control Panel Function State Description Control PanelLED Indicators Power ButtonKVM Connector KVM ButtonB9DR7 Mainboard MainboardB9DR7 Mainboard Layout Intel C602J/Intel 602J Chipset Block DiagramCmos Clear JumpersBlade Unit Components Hard Disk Drives Memory SupportIntroduction BiosFlashing Bios Bios UpdatesType flash filename.rom Running SetupMenu Option Description Main Bios SetupMain Bios Setup Menu Options Advanced Setup Menu Options Advanced SetupBoot Feature Submenu Sub-menu DescriptionCPU Configuration Submenu Menu Option Boot Feature Submenu Menu OptionBios Chipset Configuration Sub-menu Menu Option Sata Configuration Sub-menu Menu Option SuperIO Device Configuration Sub-menu PCIe/PCI/PnP Configuration Sub-menu Menu OptionSerial Port Console Redirection Sub-menu SuperIO Device Configuration Sub-menu Menu OptionCOM2 Serial Port Console Redirection Sub-menu Menu Option11. ME Subsystem Sub-menu Menu Option 10. Acpi Settings Sub-menu Menu Option12. Event Logs Menu Menu Option Event Logs Setup13. Ipmi Menu Menu Option Ipmi Setup14. Boot Setup Menu Options BootSecurity 15. Security Menu Options16. Exit Menu Options Save & ExitSBI-7127R-S6 Blade Module User’s Manual Table A-1. Bios Post Messages Bios Message Bios Post MessagesSBI-7427R-S3/T3 Blade Module User’s Manual Bios Post Codes Terminal Post Errors Recoverable Post ErrorsTable A-2. Terminal Post Errors Post Code DescriptionAppendix a Bios Post Codes SBI-7427R-S3/T3 Blade Module User’s Manual Table A-2. Terminal Post Errors Post Code Table A-3. Boot Block Flash ROM Terminal Post Errors Appendix a Bios Post Codes SBI-7427R-S3/T3 Blade Module User’s Manual Disclaimer SBI-7127R-S6 Blade Module User’s Manual