Shure UP4 manual UC1/UC2/U1/U2 Transmitter Setup, System Operation

Page 3

ENGLISH

 

ENGLISH

QUICK SETUP GUIDE FOR THE SHURE UP WIRELESS SYSTEM UP4 Receiver Setup and Camera Mounting

 

 

 

 

 

To power supply

To audio input

(If not using interior battery power)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ATTACHING THE MOUNTING BOX, INSTALLING THE UP4 RECEIVER

FIGURE 1

1.Open the battery compartment on the UP4 receiver and insert a fresh 9 volt battery if battery power is to be used. Attach the two antennas to the ANTENNA IN SMA connectors.

2.Attach the mounting box to the video camera (see Attaching the Mounting Box to a Camera).

3.Insert the UP4 receiver into the mounted box. Connect the audio cable from the UP4 audio output into the audio input(s) of the video camera. If not using the receiver’s battery, attach a cable from the receiver’s dc jack to the camera’s battery port. (See Installing the UP4 Receiver)

4.Set the Push-Lock Audio Gain Pot to the appropriate level for the camera sound input or other equipment you are using.

5.Move the receiver’s power switch to the ON position.

Note: If you encounter RF interference, change the Group and Channel setting on the transmitter and the receiver. Refer to the supplement for additional frequency information.

UC1/UC2/U1/U2 Transmitter Setup

1.Open the battery cover and insert a fresh 9V alkaline battery (UC1/UC2) or two 1.5V AA batteries (U1/U2)

2.Make sure the transmitter Group and Channel settings match those of the receiver. If they do not, adjust settings using either a screwdriver (UC1 and UC2) or the electronic controls (U1 and U2).

3.Close the battery cover.

System Operation

1.Turn the transmitter on and speak into the microphone.

2.On the UP4 receiver, the PWR LED, RF LED and AUD LED should illuminate green, indicating that the receiver is receiving the transmitter signal.

3.If the AUD LED on the receiver glows red steadily when you are speaking in a normal voice, try adjusting the transmitter gain until the AUD LED glows green on the receiver. The AUD LED should flash red when you speak loudly.

– 1 –

Image 3
Contents UP Portable UHF Wireless System User Guide Table of Contents System Operation UC1/UC2/U1/U2 Transmitter SetupSystem Features System DescriptionUC1 UC2 UP4 AUD UP4 Receiver FeaturesUC2 Transmitter Features and Controls UC1 Transmitter Features and ControlsU2 Transmitter Controls & Indicators U1 Transmitter Controls & IndicatorsU1 and U2 Transmitter Checking BatteriesUP4 Receiver UC1 and UC2 TransmitterUC1 Installing BatteriesUC1 or U1 Body-Pack Transmitter UC2 or U2 Hand-Held TransmitterChanging U1 and U2 Transmitter Group/Channel Settings Changing Group and Channel SettingsChanging the UP4 Receiver Group/Channel Setting Changing the UC1 or UC2 Transmitter Group/Channel SettingsActivating the Frequency Lock Function U1 and U2 Locking the Power on U1 and U2Attaching a Second Mounting Box UP4 Receiver SET UPAttaching The UP4 Receiver Antennas Attaching the Mounting Box to a CameraPower Cable Installing the UP4 ReceiverAttaching the WEATHER-RESISTANT Cover Operating the UP System with UC1 or U1 BODY-PACK U1 Attenuator Switch Changing the Transmitter SettingsAdjusting the Transmitter Gain Level UC1 Attenuator SwitchTroubleshooting System SpecificationsTips for Achieving Optimum Performance BODY-PACK Transmitter Specifications HAND-HELD Transmitter SpecificationsUP4 Receiver Specifications Furnished Accessories Optional AccessoriesReplacement Parts Declaration of Conformity Additional Information for this Shure Wireless SystemGarantia Limitada Limited WarrantyGarantie Limitée Beschränkte Gewährleistung