Shure UP4 manual UC1 Transmitter Features and Controls, UC2 Transmitter Features and Controls

Page 6

ENGLISH

1 2 3 4

1

2

3

4

5

68

79

10

11

12

FIGURE 4

UC1 TRANSMITTER FEATURES AND CONTROLS

1.Antenna. A flexible 1/4 wave whip antenna is permanently attached to the top of the UC1 Body-Pack transmitter.

2.Power/Battery Fuel Gauge. When the Power switch is in the ON position, one of the three LEDs will glow, indicating that the transmitter is on. The LED color indicates the amount of battery life remaining. Refer to the Checking Bat- teries section.

3.ON/OFF Switch. Turns transmitter power on and off.

4.Input Connector (LEMO connector optional). This Mini connector (TA4F ) provides connection with a variety of lavali- er, instrument and headset microphones and cables. LEMO connectors are available as an option.

5.Remote Mute Switch Input Connector. When used with the optional Shure UA101 Remote Mute Switch, this 3.5 mm connector lets you remotely mute the body pack during a performance.

6.Group Setting Control (Red Switch). Rotating this switch clockwise advances the Group setting. Rotating it counter- clockwise decreases the Group setting. Use the supplied screwdriver to make adjustments.

7.Channel Setting Control (Green Switch). Rotating this switch clockwise advances the Channel setting. Rotating it counterclockwise decreases the Channel setting. Use the supplied screwdriver to make adjustments.

8.Input Attenuation Control. This two position switch lets you select either 0 dB or –20 dB attenuation, depending on the input source and application. For most microphone ap- plications, the 0 dB setting is appropriate.

9.Audio Gain Control. This control changes the audio level to accommodate different sound sources. The factory set- ting is at mid level, which is appropriate for most microphone applications, except headphone microphones (Refer to the “Adjusting the Transmitter Gain Level” section). Use the supplied screwdriver to make adjustments.

10.Battery Compartment. One 9V battery is required.

11.Battery Compartment Cover. Hinged cover on front sur- face opens to expose the battery and Group/Channel, Gain, and Attenuation controls.

12.Battery Cover Release Tabs. Squeeze these two tabs to- gether to release the battery cover.

13.Belt Clip (not shown). Allows the transmitter to be worn on a belt, waistband, or guitar strap. The belt clip can be rotated 180°.

ENGLISH

1

2

3

4

5

6

7

8

FIGURE 5

UC2 TRANSMITTER FEATURES AND CONTROLS

1.Grille. This protects the microphone cartridge and helps re- duce breath sounds and wind noise. The grilles for the vari- ous microphone heads differ in appearance.

2.Power Indicator/Battery Fuel Gauge. When the UC2 is turned on, one of three LEDs will glow, indicating that power is on and the amount of battery life remaining. Refer to the “Checking Transmitter Battery” paragraph for more informa- tion on battery life.

3.Power Switch. This switch turns the transmitter on and off.

4.Audio Gain Control. This control changes the audio level to accommodate various sound sources (e.g. singing or speaking). Use the supplied screwdriver to make adjust- ments. Refer to the “Adjusting the Transmitter Gain Level” paragraph.

5.Group Setting Control (Red Switch). Rotating this switch clockwise advances the Group setting. Rotating it counterclock- wise decreases the Group setting. Use the supplied screwdriv- er to change the setting.

6.Channel Setting Control (Green Switch). Rotating this switch clockwise advances the Channel setting. Rotating it counterclockwise decreases the Channel setting. Use the supplied screwdriver to make adjustments.

7.9 V Battery. Access the battery by unscrewing the battery cover.

8.Battery Cover. Unscrew this to expose the battery and the Group, Channel and Gain controls.

– 4 –

Image 6
Contents UP Portable UHF Wireless System User Guide Table of Contents UC1/UC2/U1/U2 Transmitter Setup System OperationSystem Features System DescriptionUC1 UC2 UP4 UP4 Receiver Features AUDUC1 Transmitter Features and Controls UC2 Transmitter Features and ControlsU1 Transmitter Controls & Indicators U2 Transmitter Controls & IndicatorsUC1 and UC2 Transmitter Checking BatteriesUP4 Receiver U1 and U2 TransmitterUC2 or U2 Hand-Held Transmitter Installing BatteriesUC1 or U1 Body-Pack Transmitter UC1Changing the UC1 or UC2 Transmitter Group/Channel Settings Changing Group and Channel SettingsChanging the UP4 Receiver Group/Channel Setting Changing U1 and U2 Transmitter Group/Channel SettingsLocking the Power on U1 and U2 Activating the Frequency Lock Function U1 and U2Attaching the Mounting Box to a Camera UP4 Receiver SET UPAttaching The UP4 Receiver Antennas Attaching a Second Mounting BoxInstalling the UP4 Receiver Power CableAttaching the WEATHER-RESISTANT Cover Operating the UP System with UC1 or U1 BODY-PACK UC1 Attenuator Switch Changing the Transmitter SettingsAdjusting the Transmitter Gain Level U1 Attenuator SwitchTroubleshooting System SpecificationsTips for Achieving Optimum Performance BODY-PACK Transmitter Specifications HAND-HELD Transmitter SpecificationsUP4 Receiver Specifications Furnished Accessories Optional AccessoriesReplacement Parts Additional Information for this Shure Wireless System Declaration of ConformityBeschränkte Gewährleistung Limited WarrantyGarantie Limitée Garantia Limitada