Shure UP4 Installing Batteries, UC1 or U1 Body-Pack Transmitter, UC2 or U2 Hand-Held Transmitter

Page 9

ENGLISH

 

ENGLISH

INSTALLING BATTERIES

UP4 Receiver

FIGURE 11

1.Locate the battery door on the bottom of the unit. Release the battery door by sliding the door in the direction of the arrow until the pins on either side of the door are visible. Flip open the battery door once it is released.

2.Insert a fresh 9 volt battery, with terminals facing down, observing the proper polarity (+/–).

3.Return the battery door to its original position and slide the pins back into the lock position.

NOTE: The battery door can be opened when the UP4 receiver is mounted on a camera, allowing the battery to be replaced without dismounting the unit. If two receivers are mounted on the same camera, the top receiver and box will need to be dismounted in order to open the battery door on the bottom unit.

UC1 or U1 Body-Pack Transmitter

UC1

U1

FIGURE 12

1. Make sure the transmitter power ON/OFF switch is in the OFF position.

1.5V AA

1.5V AA

2.Open the transmitter battery compartment by squeezing the two tabs on either side of the transmitter. Then flip the battery cover down. Refer to Figure 12.

3.To remove battery:

UC1: Lift up on the edge of the battery remove it.

U1: Press down on negative terminal end of each battery.

4. Insert a new 9V battery (UC1) or two fresh 1.5V AA batteries (U1) in the compartment. Maintain proper battery polarity (”+/–”).

UC2 or U2 Hand–Held Transmitter

UC2

U2

FIGURE 13

1.Make sure the transmitter power ON/OFF switch is in the OFF position.

2.Unscrew the battery cover. On the U2, Slide the cover down once it has been unscrewed.

3.Pull down on the old battery and remove it (UC2) or lift the batteries out (U2).

4.Install a fresh 9V alkaline battery (UC2) or two fresh 1.5 V AA batteries (U2). Maintain proper battery polarity (”+/–”). Screw the battery cover back into place.

– 7 –

Image 9
Contents UP Portable UHF Wireless System User Guide Table of Contents System Operation UC1/UC2/U1/U2 Transmitter SetupSystem Features System DescriptionUC1 UC2 UP4 AUD UP4 Receiver FeaturesUC2 Transmitter Features and Controls UC1 Transmitter Features and ControlsU2 Transmitter Controls & Indicators U1 Transmitter Controls & IndicatorsUP4 Receiver Checking BatteriesUC1 and UC2 Transmitter U1 and U2 TransmitterUC1 or U1 Body-Pack Transmitter Installing BatteriesUC2 or U2 Hand-Held Transmitter UC1Changing the UP4 Receiver Group/Channel Setting Changing Group and Channel SettingsChanging the UC1 or UC2 Transmitter Group/Channel Settings Changing U1 and U2 Transmitter Group/Channel SettingsActivating the Frequency Lock Function U1 and U2 Locking the Power on U1 and U2Attaching The UP4 Receiver Antennas UP4 Receiver SET UPAttaching the Mounting Box to a Camera Attaching a Second Mounting BoxPower Cable Installing the UP4 ReceiverAttaching the WEATHER-RESISTANT Cover Operating the UP System with UC1 or U1 BODY-PACK Adjusting the Transmitter Gain Level Changing the Transmitter SettingsUC1 Attenuator Switch U1 Attenuator SwitchTroubleshooting System SpecificationsTips for Achieving Optimum Performance BODY-PACK Transmitter Specifications HAND-HELD Transmitter SpecificationsUP4 Receiver Specifications Furnished Accessories Optional AccessoriesReplacement Parts Declaration of Conformity Additional Information for this Shure Wireless SystemGarantie Limitée Limited WarrantyBeschränkte Gewährleistung Garantia Limitada