Shure UP4 manual Tips for Achieving Optimum Performance, Troubleshooting, System Specifications

Page 17

ENGLISH

 

ENGLISH

TIPS FOR ACHIEVING OPTIMUM PERFORMANCE

Maintain a line of sight between the transmitter and receiver antennas.

Use the proper receiver antennas.

Do not obstruct the receiver antennas.

Avoid operating near metal objects.

Never use two transmitters set to the same frequency concurrently.

Keep distance between transmitter and receiver as short as possible.

Monitor the UP4’s PWR LED; if the PWR LED goes into low battery mode (red light) replace old battery with a fresh battery immediately.

For added protection, replace batteries before each shoot.

TROUBLESHOOTING

Some common problems and their solutions are identified in the table below. If you are unable to solve a problem, contact your dealer or the Shure Service Department at 1-800-516-2525 (7:30 am to 4:00 pm, Central Standard Time). In Europe, call 49-7131-72140; other international users call Shure in the U.S.A. at 847-866-2200.

Problem

Solution

 

 

No sound; receiver RF LED and

Make sure transmitter and receiver are turned on.

AUD LEDs not glowing.

Check transmitter Power/Battery Gauge. Replace battery if necessary.

 

 

Make sure transmitter and receiver frequency Group/Channel settings are identical.

 

Check receiver antenna connection(s).

 

Make sure an antenna is in the line of sight of the transmitter. If necessary, reduce the distance between

 

transmitter and receiver.

 

 

No receiver sound; RF and AUD LEDs

Check for proper connection between receiver and camera.

glowing.

Talk into the microphone and observe the receiver AUD LED. If it glows, the problem is elsewhere in

 

 

the sound system.

 

Check output gain setting

 

 

Received signal is noisy or contains ex-

Check transmitter Power/Battery Fuel Gauge and replace battery if power is low.

traneous sounds with transmitter on.

Remove local sources of RF interference, such as lighting equipment.

 

 

Two transmitters may be operating on the same frequency. Locate and turn one off or change frequency.

 

Signal may be too weak. Reposition antennas closer to the transmitter.

 

Make sure the antennas are properly attached.

 

Turn the UP4 receiver to the On (Tone Key Off) position. This will allow the receiver to pass noisy or

 

unwanted interfering signals. If interfering signals are detected, change frequencies on both the receiv-

 

er and the transmitter.

 

 

Noise from receiver with transmitter off.

Remove local sources of RF interference, such as lighting equipment.

 

Try using another frequency.

 

Reposition the receiver or antennas.

 

 

Momentary loss of sound as transmitter

Reposition receiver and perform a “walkthrough” test and observe the RF LED. If audio dropouts per-

is moved around usage area.

sist, mark these “dead spots” in the usage area and avoid them.

 

 

SYSTEM SPECIFICATIONS

RF Carrier Frequency Range

Approximately 692 to 862 MHz (Available frequencies depend on applicable regulations in country where system is used). Operating Range:152.4 m (500 ft) under typical conditions

Audio Frequency Response: 45 to 15,000 Hz, $3 dB

Image Rejection: > 90 dB typical

Spurious Rejection: >80 dB typical

System Distortion (ref. 45 kHz deviation, 1 kHz modulation): 0.4% THD typical

Signal/Noise Ratio:

UA, UB: 100 dB (ref. 45 kHz deviation)

MB: >80 dB (ref. 27 kHz deviation)

KK:>80 dB (ref.  23 kHz deviation)

Sensitivity: –110 dBm for 12 dB SINAD typical

Operating Temperature Range

–28.9°to 57.2° C (–20 to 135° F) NOTE: Battery characteristics may limit this range.

Battery Life

U1*, U2*: 12 hours

UC1**UC2**: 8 hours

UP4**: 10 hours

*with two 1.5 V AA batteries.

**with 9 V alkaline battery (Duracell MN1604 recommended).

– 15 –

Image 17
Contents UP Portable UHF Wireless System User Guide Table of Contents System Operation UC1/UC2/U1/U2 Transmitter SetupUC1 UC2 UP4 System FeaturesSystem Description AUD UP4 Receiver FeaturesUC2 Transmitter Features and Controls UC1 Transmitter Features and ControlsU2 Transmitter Controls & Indicators U1 Transmitter Controls & IndicatorsUP4 Receiver Checking BatteriesUC1 and UC2 Transmitter U1 and U2 TransmitterUC1 or U1 Body-Pack Transmitter Installing BatteriesUC2 or U2 Hand-Held Transmitter UC1Changing the UP4 Receiver Group/Channel Setting Changing Group and Channel SettingsChanging the UC1 or UC2 Transmitter Group/Channel Settings Changing U1 and U2 Transmitter Group/Channel SettingsActivating the Frequency Lock Function U1 and U2 Locking the Power on U1 and U2Attaching The UP4 Receiver Antennas UP4 Receiver SET UPAttaching the Mounting Box to a Camera Attaching a Second Mounting BoxPower Cable Installing the UP4 ReceiverAttaching the WEATHER-RESISTANT Cover Operating the UP System with UC1 or U1 BODY-PACK Adjusting the Transmitter Gain Level Changing the Transmitter SettingsUC1 Attenuator Switch U1 Attenuator SwitchTips for Achieving Optimum Performance TroubleshootingSystem Specifications UP4 Receiver Specifications BODY-PACK Transmitter SpecificationsHAND-HELD Transmitter Specifications Replacement Parts Furnished AccessoriesOptional Accessories Declaration of Conformity Additional Information for this Shure Wireless SystemGarantie Limitée Limited WarrantyBeschränkte Gewährleistung Garantia Limitada