SMC Networks SMCWBR14-N manual Allow RIP updates from WAN, RIP Password, Dhcp Server Settings

Page 24

Make this router the preferred destination for packets that are not otherwise destined.

Allow RIP updates from WAN

For security, disable this option unless required by the ISP.

RIP Password

RIP Version 2 supports the use of a password to limit access to routers through the RIP protocol. If the ISP or other LAN router requires a RIP password, enter the password here.

DHCP Server Settings

DHCP stands for Dynamic Host Configuration Protocol. The DHCP section is where you configure the built-in DHCP Server to assign IP addresses to the computers and other devices on your local area network (LAN).

Enable DHCP Server

Once your router is properly configured and this option is enabled, the DHCP Server will manage the IP addresses and other network configuration information for computers and other devices connected to your Local Area Network. There is no need for you to do this yourself.

The computers (and other devices) connected to your LAN also need to have their TCP/IP configuration set to "DHCP" or "Obtain an IP address automatically".

When you set Enable DHCP Server, the following options are displayed.

DHCP IP Address Range

These two IP values (from and to) define a range of IP addresses that the DHCP Server uses when assigning addresses to computers and devices on your Local Area Network. Any addresses that are outside of this range are not managed by the DHCP Server; these could, therefore, be used for manually configured devices or devices that cannot use DHCP to obtain network address details automatically.

It is possible for a computer or device that is manually configured to have an address that does reside within this range. In this case the address should be reserved (see Static DHCP Client below), so that the DHCP Server knows that this specific address can only be used by a specific computer or device.

Your router, by default, has a static IP address of 192.168.2.1. This means that addresses 192.168.2.2 to 192.168.2.254 can be made available for allocation by the DHCP Server.

Example:

Your router uses 192.168.2.1 for the IP address. You've assigned a computer that you want to designate as a Web server with a static IP address of 192.168.2.3. You've assigned another computer that you want to designate as an FTP server with a static IP address of 192.168.2.4. Therefore the starting IP address for your DHCP IP address range needs to be 192.168.2.5 or greater.

Example:

Suppose you configure the DHCP Server to manage addresses From: 192.168.2.100

To: 192.168.2.199. This means that 192.168.2.3 to 192.168.2.99 and 192.168.2.200 to 192.168.2.254 are NOT managed by the DHCP Server. Computers or devices that use addresses from these ranges are to be manually configured. Suppose you have a web server computer that has a manually configured address of 192.168.2.100. Because

21

Page 23 Page 25
Image 24
Page 23 Page 25
Contents User Guide Limited Warranty Page CE Mark Declaration of Conformance for EMI and Safety EEC Important NoteFCC Radiation Exposure Statement IiiTable of Contents Getting Started with the SMCWBR14-N Package Contents Wireless LAN Networking AD-HOCIBSS NetworkPage Page Roaming in an ESS network diagram Introduction Hardware Overview Front Panel LED’s Getting Started Using the Configuration Menu ¾ Click LogBasic BasicInternetBasicWireless WEP Example WPA-Personal and WPA-EnterpriseWPA-Personal Advanced Optional Backup Radius Server BasicNetwork Settings Router Settings Enable RIPRIP Operating mode Act as default routerAllow RIP updates from WAN RIP PasswordDhcp Server Settings Enable Dhcp ServerDhcp Lease Time Always BroadcastAdd/Edit Dhcp Reservation Computer NameDhcp Reservations List Number of Dynamic Dhcp ClientsRevoke ReserveAdvanced AdvancedVirtual ServerVirtual Server Parameters Name ProtocolPrivate Port Public PortEnable Add/Edit Virtual ServerSave Virtual Servers ListAdvancedSpecial Applications Parameters for an Application Rule ExampleApplication Trigger Port RangeTrigger Protocol Input Port RangeInput Protocol Add/Edit Special Applications RuleAdvancedGaming Port Forwarding Fields NameTCP Ports To Open UDP Ports To OpenEdit/Add Game Rule Game Rules ListStreamEngine Setup Enable StreamEngine AdvancedStreamEngineAutomatic Classification Dynamic FragmentationAutomatic Uplink Speed Measured Uplink SpeedAdd/Edit StreamEngine Rule Enable PrioritySource IP Range Source Port RangeAdvancedRouting Add/Edit RouteRoutes List AdvancedAccess Control Policy WizardAdd Policy Policy TablePage AdvancedWEB Filter Web Filter Parameters Web SiteAdd/Edit Web Site Allowed Web Site List Enable MAC Address Filter Filter Settings ModeFilter Wireless Clients AdvancedMAC Address FilterFilter Wired Clients Add/Edit MAC AddressMAC Address List AdvancedFirewall Firewall Settings Enable SPI NAT Endpoint FilteringEndpoint Independent Address RestrictedEnable DMZ DMZ IP AddressPptp RtspFTP Netmeeting SIPWake-On-LAN MMSAdvancedInbound Filter Add/Edit Inbound Filter Rule ActionInbound Filter Rules List Allow AllAdvancedAdvanced Wireless 802.11d Enable WMM EnableExtra Wireless Protection WDS EnableEnable UPnP Enable WAN Ping RespondAdvancedNetwork UPnPEnable Multicast Streams WAN Port SpeedMulticast Streams ToolsAdmin Admin PasswordUser Password Enable Remote ManagementRemote Admin Port Remote Admin Inbound FilterToolsTime Time Configuration Current Router Time Enable Daylight SavingAutomatic Time Configuration Enable NTP Server Time ZoneEnable Logging to Syslog Server ToolsSyslogSyslog Server IP Address ToolsEmail Settings Password Verify PasswordEmail Log When Full or on Schedule On Log Full On ScheduleSave Settings To Local Hard Drive Load Settings From Local Hard DriveRestore To Factory Default Settings Reboot The DeviceFirmware Upgrade ToolsFirmwareFirmware Information Check OnlineUpload ToolsDynamic DNS Verify Password or Key TimeoutToolsSystem Check ToolsSchedules Schedule Rules List StatusDevice info Statistics and Active SessionsPage Dhcp Connection PPPoE, PPTP, L2TP ConnectionBigPond Connection LAN ComputersStatusWireless SignalRate StatusRouting Apply Log Settings Now StatusLogsWhat to View View LevelsRefresh ClearEmail Now Save LogStatusStatistics Errors StatusActive Sessions InternalExternal NATDir OutTime Out SecondsAdsl AsciiBootp CAT Dhcp DMZDNS DSLEAP GUI Http HttpsIcmp IeeeIPX ISPLAN LEDLPR/LPD L2TPMdix MIBMppe MTUNIC NTPOfdm OSIPPP RadiusRIP RSA SmtpSnmp SohoSsid TCPTCP/IP TftpURL USBUTP VlanWDS WispWlan WPAYagi antenna 802.11Technical Support

SMCWBR14-N specifications

The SMC Networks SMCWBR14-N is a wireless router that has established itself as a reliable choice for both home and small office environments. This device is renowned for its balance of performance, flexibility, and cost-effectiveness, making it a popular option among budget-conscious consumers looking for stable connectivity.

One of the primary features of the SMCWBR14-N is its compliance with the IEEE 802.11n wireless standard. This technology allows it to deliver significantly higher data rates than older standards like 802.11g, making it ideal for tasks such as streaming video, online gaming, and large file transfers. It operates on both the 2.4 GHz frequency band, which provides extensive coverage range, and it can reach speeds of up to 300 Mbps. This dual-band functionality ensures that multiple devices can connect simultaneously without significant interference.

The router comes equipped with four 10/100 Mbps Ethernet ports, enabling wired connections for devices such as gaming consoles, desktop computers, and smart TVs. The data transfer rates over wired connections are stable, ensuring low latency and reliable performance, which is essential for users engaged in intensive online activities.

A notable feature of the SMCWBR14-N is its built-in firewall and various security options. This includes Wi-Fi Protected Access (WPA/WPA2) encryption, which significantly enhances the security of the wireless network. The router also supports MAC address filtering, which allows users to define which devices can connect to the network, adding an additional layer of security.

Configuration and management of the SMCWBR14-N are user-friendly, thanks to its web-based interface. Users can easily access the settings via any web browser, allowing for quick adjustments and monitoring of the network. The router supports Quality of Service (QoS) features, enabling users to prioritize bandwidth for specific applications, thus ensuring a smooth operation for real-time activities like VoIP calls and video conferencing.

Furthermore, the SMCWBR14-N supports various advanced features such as DHCP server functionality and dynamic DNS, making it suitable for users who desire a more hands-on approach to their networking setup.

In summary, the SMC Networks SMCWBR14-N wireless router is an excellent choice for individuals and small businesses seeking a robust and versatile networking solution. Its blend of high-speed wireless connectivity, comprehensive security options, and easy management makes it a compelling option for navigating the demands of modern internet usage.
Top Page Image Contents