SMC Networks SMC7904BRB2 manual Rip

Page 77

CONFIGURATION PARAMETERS

RIP

Parameter	Description

General RIP Parameters
RIP mode	Globally enables or disables RIP.
Auto summary	If Auto summary is disabled, then RIP packets will
	include sub-network information from all sub-
	networks connected to the router. If enabled, this
	sub-network information will be summarized to
	one piece of information covering all sub-
	networks.
Table of current Interface RIP
parameter
Interface	The WAN interface to be configured.
Operation Mode	Disable: RIP disabled on this interface.
	Enable: RIP enabled on this interface.
	Silent: Listens for route broadcasts and updates its
	route table. It does not participate in sending route
	broadcasts.
Version	Sets the RIP (Routing Information Protocol)
	version to use on this interface.

4-39

Image 77

Contents Page Page Router with built-in ADSL2/2+ Modem Trademarks Limited Warranty Limited Warranty Federal Communication Commission Interference Statement CompliancesEC Conformance Declaration Safety Compliance Wichtige Sicherheitshinweise Germany Compliances Table of Contents Configuring the BarricadeTM Vii Viii About the Barricade Features and BenefitsInternet Access Wired LANApplications Shared IP AddressDMZ Host Support Virtual ServerSecurity Virtual Private Network VPNIntroduction Package Contents Chapter InstallationHardware Description System RequirementsSMC7904BRA2 Rear Panel SMC7904BRB2 Rear Panel SMC7904BRA2 Front Panel LED Indicators SMC7904BRA2SMC7904BRB2 Front Panel LED Indicators SMC7904BRB2Connect the Adsl Line ISP SettingsConnect the System Connect the Power Adapter Attach to Your Network Using Ethernet CablingConnection Illustration Installation TCP/IP Configuration Configuring Client PCProperties WindowsDial-Up Connections Accessories/ Command Prompt Disable Http ProxyObtain IP Settings from Your Barricade Configuring Client PC Windows XP Obtain IP Settings from Your Barricade System Preferences Configuring Your Macintosh ComputerInternet Explorer Uncheck all check boxes and click OK Configuring Client PC Chapter Configuring Barricadetm Navigating the Management Interface Making Configuration Changes Time Zone Setup WizardParameter Setting Parameter Setting Country or ISP Not Listed Parameter Description PPPoEPPPoA Your ISP Bridging DhcpBridging Static Routing Bridging Routing Dhcp ISP ConfirmSetup Wizard Menu Description Configuration parametersDdns System Time SettingsPassword Settings Remote Management WAN ATM PVC Bridging ATM InterfacePPPoA Routing PPPoE IP Over RFC1483 bridged Clone MAC Address DNS LAN IP LANVlan Vlan Profile NAT Address Mapping Virtual Server Special Application NAT Mapping Table Static Route RoutingRIP This method provides very little security as it Routing Table Firewall Access Control Configuring the Barricadetm MAC Filter URL Blocking Schedule Rule Configuring the Barricadetm Intrusion Detection Intrusion Detection Feature Configuring the Barricadetm Stateful Packet Inspection Connection Policy Parameter Defaults DescriptionHigh DoS Criteria and Port Scan CriteriaDMZ Snmp Community Trap Upnp QOS Traffic Mapping Traffic Statistics Adsl Parameters AdslAdsl Status Error Interleaved Path Ddns Ping Utility ToolsTrace Route Utility Configuration Tools Firmware Upgrade Reset Status Configuring the Barricadetm Following items are included on the Status screen Windows NT4/2000/XP Finding the MAC address of a Network CardMacintosh LinuxAppendix a Troubleshooting Hosts on the attached LAN. However, if you manually Troubleshooting Chart Troubleshooting Ethernet Cable SpecificationsWiring Conventions RJ-45 Port Connection Figure B-1. RJ-45 Ethernet Connector Pin NumbersPin Assignments Straight-Through WiringCrossover Wiring Adsl Cable Figure B-2. RJ-11 Connector Pin NumbersFigure B-3. RJ-11 Pinouts Adsl Features Physical Characteristics PortsATM Features Management FeaturesLAN Features Security FeaturesTemperature IEC Weight 500 g Input Power 12 V 1 a Ieee Standards

Related manuals

Manual 2 pages 37.56 Kb