SMC Networks 1000 manual Rack Mounting

Page 33

INSTALLING THE SWITCH

Mounting

A TigerSwitch 1000 unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting instructions for each type of site follow.

Rack Mounting

Before rack mounting the switch, pay particular attention to the following factors:

◆Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating temperature range. (See Appendix C)

◆Mechanical Loading: Do not place any equipment on top of a rack-mounted unit

◆Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded.

◆Grounding: Rack-mounted equipment should be properly grounded. Particular attention should be given to supply connections other than direct connections to the mains.

To rack-mount devices:

1.Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.

3-3

Image 33

Contents TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesIndustry Canada Class a Japan Vcci Class aEC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aSafety Compliance Warnhinweis Faseroptikanschlüsse Optische SicherheitUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Compliances Table of Contents Specifications C-1 Troubleshooting A-1Making Network Connections Cables B-1Ordering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About TigerswitchDescription of Hardware 1000BASE-T PortsGbic Slots Port and System LEDs Status LEDsNetwork Management Agent VLANs Spanning Tree ProtocolPower Supply Receptacles Optional Redundant Power UnitMulticast Switching Traffic PriorityFeatures and Benefits ConnectivityPerformance Management Chapter Network Planning Introduction to SwitchingBackbone Consolidation Sample ApplicationsMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX Maximum Fiber Optic Cable Distance for 1000BASE-LXMbps Fast Ethernet Collision Domain Maximum 100BASE-TX Network Diameter Using RepeatersSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I RepeatersMbps Ethernet Collision Domain Application NotesSMC 5-4-3 Rule Maximum Cable LengthSelecting a Site Installing the SwitchEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling a Gbic Transceiver Power Receptacle Connecting to a Power SourceInstalling the Switch Chapter Making Network Connections Connecting Network DevicesConnecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems In-Band Access InstallationAppendix B Cables Specifications1000BASE-T Pin Assignments Twisted-Pair Cable and Pin AssignmentsPin MDI Signal Name MDI-X Signal Name Cable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling1000BASE-T Cable Requirements DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCPhysical Characteristics Appendix C SpecificationsSwitch Features Standards Management FeaturesSafety WarrantyCompliances EmissionsAppendix D Ordering Information Ordering Information Glossary-1 Glossary1000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7Glossary-8 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call