SMC Networks 1000 manual Status LEDs, Port and System LEDs

Page 19

ABOUT THE TIGERSWITCH 1000

Status LEDs

The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table.

Figure 1-2. Port and System LEDs

Port and System Status LEDs

LED	Condition	Status

Power	On Green	Switch is receiving power.

	Off	Power off or failure.

RPU	On Green	Redundant power unit is attached and
		is operating in a load-sharing mode.

	Off	Power off or failure.

Diag.	Flashing Green	System self-diagnostic test in progress.

	On Green	System self-diagnostic test successfully
		completed.

	On Amber	System self-diagnostic test has failed.

1-3

Image 19

Contents TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty Japan Vcci Class a CompliancesFCC Class a Industry Canada Class aEC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aWarnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Compliances Table of Contents Cables B-1 Troubleshooting A-1Specifications C-1 Making Network ConnectionsOrdering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About Tigerswitch1000BASE-T Ports Description of HardwareGbic Slots Port and System LEDs Status LEDsNetwork Management Agent VLANs Spanning Tree ProtocolTraffic Priority Optional Redundant Power UnitPower Supply Receptacles Multicast SwitchingConnectivity Features and BenefitsPerformance Management Chapter Network Planning Introduction to SwitchingBackbone Consolidation Sample ApplicationsMaking Vlan Connections Making Vlan ConnectionsMaximum Fiber Optic Cable Distance for 1000BASE-LX Connectivity RulesMbps Gigabit Ethernet Collision Domain Maximum Fiber Optic Cable Distance for 1000BASE-SXSMC 2-1 Rule for Class I Repeaters Maximum 100BASE-TX Network Diameter Using RepeatersMbps Fast Ethernet Collision Domain SMC 3-2 Rule for Class II RepeatersMaximum Cable Length Application NotesMbps Ethernet Collision Domain SMC 5-4-3 RuleSelecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling a Gbic Transceiver Power Receptacle Connecting to a Power SourceInstalling the Switch Chapter Making Network Connections Connecting Network DevicesConnecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems In-Band Access InstallationAppendix B Cables Specifications1000BASE-T Pin Assignments Twisted-Pair Cable and Pin AssignmentsPin MDI Signal Name MDI-X Signal Name Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCPhysical Characteristics Appendix C SpecificationsSwitch Features Standards Management FeaturesEmissions WarrantySafety CompliancesAppendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 1000BASE-TGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7Glossary-8 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call