SMC Networks 1000 manual Desktop or Shelf Mounting, Attaching the Adhesive Feet

Page 35

INSTALLING THE SWITCH

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

5.If also installing RPUs, mount them in the rack below the other devices.

Desktop or Shelf Mounting

1. Attach the four adhesive feet to the bottom of the first switch.

Figure 3-3. Attaching the Adhesive Feet

2.Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

5.If also installing RPUs, place them close to the stack.

3-5

Image 35

Contents TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty Japan Vcci Class a CompliancesFCC Class a Industry Canada Class aEC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aUnderwriters Laboratories Compliance Statement Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Wichtige Sicherheitshinweise Germany Compliances Table of Contents Cables B-1 Troubleshooting A-1Specifications C-1 Making Network ConnectionsOrdering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About TigerswitchGbic Slots Description of Hardware1000BASE-T Ports Port and System LEDs Status LEDsNetwork Management Agent VLANs Spanning Tree ProtocolTraffic Priority Optional Redundant Power UnitPower Supply Receptacles Multicast SwitchingPerformance Features and BenefitsConnectivity Management Chapter Network Planning Introduction to SwitchingBackbone Consolidation Sample ApplicationsMaking Vlan Connections Making Vlan ConnectionsMaximum Fiber Optic Cable Distance for 1000BASE-LX Connectivity RulesMbps Gigabit Ethernet Collision Domain Maximum Fiber Optic Cable Distance for 1000BASE-SXSMC 2-1 Rule for Class I Repeaters Maximum 100BASE-TX Network Diameter Using RepeatersMbps Fast Ethernet Collision Domain SMC 3-2 Rule for Class II RepeatersMaximum Cable Length Application NotesMbps Ethernet Collision Domain SMC 5-4-3 RuleSelecting a Site Installing the SwitchOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling a Gbic Transceiver Power Receptacle Connecting to a Power SourceInstalling the Switch Chapter Making Network Connections Connecting Network DevicesConnecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators In-Band Access InstallationAppendix B Cables Specifications1000BASE-T Pin Assignments Twisted-Pair Cable and Pin AssignmentsPin MDI Signal Name MDI-X Signal Name 1000BASE-T Cable Requirements Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCPhysical Characteristics Appendix C SpecificationsSwitch Features Standards Management FeaturesEmissions WarrantySafety CompliancesAppendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 1000BASE-TGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7Glossary-8 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call