SMC Networks 1000 manual Connecting to an SC-Type Fiber Port

Page 41

MAKING NETWORK CONNECTIONS

Note: For 1000 Mbps operation, all four wire pairs in the cable must be connected. 1000BASE-T ports support the Auto MDI/ MDI-X feature, which means that at any operating speed (10, 100, or 1000 Mbps), either straight-through or crossover cables can be used to connect to any server, workstation, or other network device. Make sure each twisted-pair cable does not exceed 100 meters (328 feet).

Connecting to an SC-Type Fiber Port

When connecting fiber cable to a 1000BASE-SX or 1000BASE-LX (GBIC) port on the switch, be sure you use an SC-type connector. Follow the steps below.

Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

1.Remove and keep the SC port’s rubber cover. When not connected to a fiber cable, the rubber cover should be replaced to protect the optics.

2.Check that the fiber terminators are clean. You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol. Dirty fiber terminators on fiber optic cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port.

3.Connect one end of the cable to the SC port on the switch and the other end to the SC port on the other device. Since SC connectors are keyed, the cable can be attached in only one orientation.

When inserting the cable, be sure the tab on the plug clicks into position to ensure that it is properly seated.

4-3

Image 41
Contents TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesIndustry Canada Class a Japan Vcci Class aEC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aUnderwriters Laboratories Compliance Statement Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Wichtige Sicherheitshinweise Germany Compliances Table of Contents Specifications C-1 Troubleshooting A-1Making Network Connections Cables B-1Ordering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About TigerswitchGbic Slots Description of Hardware1000BASE-T Ports Port and System LEDs Status LEDsNetwork Management Agent VLANs Spanning Tree ProtocolPower Supply Receptacles Optional Redundant Power UnitMulticast Switching Traffic PriorityPerformance Features and BenefitsConnectivity Management Chapter Network Planning Introduction to SwitchingBackbone Consolidation Sample ApplicationsMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX Maximum Fiber Optic Cable Distance for 1000BASE-LXMbps Fast Ethernet Collision Domain Maximum 100BASE-TX Network Diameter Using RepeatersSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I RepeatersMbps Ethernet Collision Domain Application NotesSMC 5-4-3 Rule Maximum Cable LengthSelecting a Site Installing the SwitchOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling a Gbic Transceiver Power Receptacle Connecting to a Power SourceInstalling the Switch Chapter Making Network Connections Connecting Network DevicesConnecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators In-Band Access InstallationAppendix B Cables Specifications1000BASE-T Pin Assignments Twisted-Pair Cable and Pin AssignmentsPin MDI Signal Name MDI-X Signal Name 1000BASE-T Cable Requirements Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCPhysical Characteristics Appendix C SpecificationsSwitch Features Standards Management FeaturesSafety WarrantyCompliances EmissionsAppendix D Ordering Information Ordering Information Glossary-1 Glossary1000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7Glossary-8 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call