SMC Networks 1000 manual Connecting to a Power Source, Power Receptacle

Page 37

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the receptacle located at the back of the device.

Figure 3-4. Power Receptacle

2. Plug the other end of the cable into a grounded, 3-pin socket.

Note: For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is lit. If not, check that the power cable is correctly plugged in.

4.If you have a purchased Redundant Power Unit, connect it to the device and to an AC power source now, following the instructions included with the package.

3-7

Image 37

Contents TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesIndustry Canada Class a Japan Vcci Class aEC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class aWarnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Compliances Table of Contents Specifications C-1 Troubleshooting A-1Making Network Connections Cables B-1Ordering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About Tigerswitch1000BASE-T Ports Description of HardwareGbic Slots Port and System LEDs Status LEDsNetwork Management Agent VLANs Spanning Tree ProtocolPower Supply Receptacles Optional Redundant Power UnitMulticast Switching Traffic PriorityConnectivity Features and BenefitsPerformance Management Chapter Network Planning Introduction to SwitchingBackbone Consolidation Sample ApplicationsMaking Vlan Connections Making Vlan ConnectionsMbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX Maximum Fiber Optic Cable Distance for 1000BASE-LXMbps Fast Ethernet Collision Domain Maximum 100BASE-TX Network Diameter Using RepeatersSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I RepeatersMbps Ethernet Collision Domain Application NotesSMC 5-4-3 Rule Maximum Cable LengthSelecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingInstalling a Gbic Transceiver Power Receptacle Connecting to a Power SourceInstalling the Switch Chapter Making Network Connections Connecting Network DevicesConnecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems In-Band Access InstallationAppendix B Cables Specifications1000BASE-T Pin Assignments Twisted-Pair Cable and Pin AssignmentsPin MDI Signal Name MDI-X Signal Name Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements DB-9 Port Pin Assignments Console Port Pin AssignmentsConsole Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PCPhysical Characteristics Appendix C SpecificationsSwitch Features Standards Management FeaturesSafety WarrantyCompliances EmissionsAppendix D Ordering Information Ordering Information Glossary-1 Glossary1000BASE-T Auto-NegotiationGlossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7Glossary-8 Index-1 IndexIndex-2 Index-3 Index-4 Page For Technical SUPPORT, Call