Seagate Medalist 17242 manual Drive mounting, Alternate capacity and master/slave jumper settings

Page 27

Medalist 17242, 13032, 10232, 8422 and 4312, Rev. A

19

Alternate capacity and master/slave jumper settings

1. The drive is shipped with a jumper on pins 7 and 8. This configures the drive for master or single drive operation.

2.Consult your computer manual to determine whether your computer supports cable select.

3.Use this jumper setting only if the drive does not work with a jumper on pins 7 and 8.

4.Use this jumper setting if your computer fails to boot because it cannot recognize drives with more than 4,092 cylinders.

	ATA interface
pin 1	connector
	2	4	6	8
4-pin power
connector	1	3	5 7

Slave

Master or single drive1

Enable cable select 2

Master with non-ATA compatible slave 3

Limit capacity to 2.1 Gbytes (4,092 cylinders) 4

Figure 2. Alternate capacity jumper and master/slave jumper

2.4 Drive mounting

You can mount the drive in any orientation using four screws in the side- mounting holes or four screws in the bottom-mounting holes. See Figure 3 on page 20 for drive mounting dimensions.

Important mounting precautions:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only 6-32 UNC mounting screws.

•The screws should be inserted no more than 0.22 inch (5.58 mm) into the bottom mounting holes and no more than 0.20 inch (5.0 mm) into the side mounting holes.

•Do not overtighten the mounting screws (maximum torque: 3 inch-lb, 0.34 N.m, 3.45 kgf.cm).

•Do not use a drive interface cable that is more than 18 inches (457 mm) long.

Image 27

Contents Product Manual Page Product Manual Page Contents ATA interface Figures Viii Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Introduction Specification summary table ST317242A ST313032A Relative humidity Gradient Formatted capacity Default logical geometryDrive Guaranteed Mbytes Bytes per Model LBA ModeDrive Model Read/Write heads MR Number of discs Supported CHS translation geometriesPhysical organization Recording and interface technologyST317242A, ST313032A Physical characteristicsDrive Specification ST310232A, ST38422A ST34312A Seek timeRead Write Seek type Msec, typ Power specificationsPower consumption Start/stop timesTypical current profile Mode Typical Watts RMS Typical Amps RMS 12VVoltage tolerance Power-management modesMode Heads Spindle Buffer Conducted noiseHumidity 3.1 Relative Humidity Environmental tolerances Ambient temperatureTemperature gradient 3.2 Wet bulb temperatureNonoperating shock AltitudeShock Operating shockElectromagnetic susceptibility Typical sound Maximum sound Mode Power belsNonoperating vibration Drive acousticsAustralian C-Tick Agency certification Safety certificationReliability Electromagnetic CompatibilityFCC verification Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Jumper settings Master/slave configuration Handling and static-discharge precautionsUltra ATA/66 cable Alternate capacity jumperDrive mounting Alternate capacity and master/slave jumper settingsMounting dimensions-top, side and end view Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a ATA interface ATA interface signals and connector pinsO pins and supported ATA signals Code ATA Interface commands Supported ATA commandsCommand name Supported by ATA-standard commandsATA-standard power-management commands Word Description Value Identify Drive commandWord Description 60-61 Total number of user-addressable Description if bit is set to Bit Word 0CH Set Features commandVendor-specific Yes 4 S.M.A.R.T. commandsA.R.T. Enable/Disable Attribute Yes Autosave A.R.T. Read Data YesD3H Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a