Seagate Medalist 17242 manual Altitude, Shock, Operating shock, Nonoperating shock, Vibration

Page 20

12Medalist 17242, 13032, 10232, 8422 and 4312, Rev. A

1.8.4 Altitude

Operating	–122 m to 3,048 m (–400 ft to 10,000+ ft)
Nonoperating	–122 m to 12,192 m (–400 ft to 40,000+ ft)

1.8.5 Shock

During shock tests, the drive was mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

1.8.5.1 Operating shock

These drives comply with the performance levels specified in this docu- ment when subjected to a maximum operating shock of 63 Gs (based on half-sine shock pulses of 2 msec). Shocks are not to be repeated more than two times per second.

1.8.5.2 Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subse- quently put into operation is 300 Gs (based on a nonrepetitive half-sine shock pulse of 2 msec duration). Shock pulses are defined by MIL-STD- 202F.

1.8.6 Vibration

During vibration tests, the drive was mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

1.8.6.1 Operating vibration

The following table lists the maximum vibration levels that the drive may experience while meeting the performance standards specified in this document.

5–22 Hz	0.020-inch displacement (peak to peak)
22–350 Hz	0.50 Gs acceleration (zero to peak)

Image 20

Contents Product Manual Page Product Manual Page Contents ATA interface Figures Viii Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Introduction Specification summary table ST317242A ST313032A Relative humidity Gradient Default logical geometry Drive Guaranteed Mbytes Bytes per ModelLBA Mode Formatted capacitySupported CHS translation geometries Physical organizationRecording and interface technology Drive Model Read/Write heads MR Number of discsPhysical characteristics Drive Specification ST310232A, ST38422A ST34312ASeek time ST317242A, ST313032APower specifications Power consumptionStart/stop times Read Write Seek type Msec, typMode Typical Watts RMS Typical Amps RMS 12V Typical current profilePower-management modes Mode Heads Spindle BufferConducted noise Voltage toleranceEnvironmental tolerances Ambient temperature Temperature gradient3.2 Wet bulb temperature Humidity 3.1 Relative HumidityAltitude ShockOperating shock Nonoperating shockTypical sound Maximum sound Mode Power bels Nonoperating vibrationDrive acoustics Electromagnetic susceptibilityAgency certification Safety certification ReliabilityElectromagnetic Compatibility Australian C-TickFCC verification Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Handling and static-discharge precautions Jumper settings Master/slave configurationAlternate capacity jumper Ultra ATA/66 cableAlternate capacity and master/slave jumper settings Drive mountingMounting dimensions-top, side and end view Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a ATA interface signals and connector pins ATA interfaceO pins and supported ATA signals ATA Interface commands Supported ATA commands Command name Supported byATA-standard commands CodeATA-standard power-management commands Identify Drive command Word Description ValueWord Description 60-61 Total number of user-addressable Description if bit is set to Bit Word Set Features command 0CH4 S.M.A.R.T. commands A.R.T. Enable/Disable Attribute Yes AutosaveA.R.T. Read Data Yes Vendor-specific YesD3H Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a