Seagate Medalist 17242 manual Environmental tolerances Ambient temperature, Temperature gradient

Page 19

Medalist 17242, 13032, 10232, 8422 and 4312, Rev. A

11

Sleep mode. The drive enters Sleep mode after receiving a Sleep command from the host. The heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Active mode with all current translation parameters intact.

Idle and Standby timers. Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary.

1.8 Environmental tolerances

1.8.1 Ambient temperature

Operating

0° to 55°C (32° to 131°F)

Nonoperating

–40° to 70°C (–40° to 158°F)

Note. Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet (3,048 meters). Operating ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

1.8.2 Temperature gradient

Operating

20°C/hour (36°F/hour) max, without condensation

Nonoperating

20°C/hour (36°F/hour) max, without condensation

1.8.3 Humidity

 

1.8.3.1

Relative Humidity

Operating

 

8% to 80% noncondensing (10% per hour max)

Nonoperating

5% to 95% noncondensing (10% per hour max)

1.8.3.2

Wet bulb temperature

Operating

 

29.4°C (84°F) max

Nonoperating

29.4°C (84°F) max

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Product Manual Page Product Manual Page Contents ATA interface Figures Viii Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Introduction Specification summary table ST317242A ST313032A Relative humidity Gradient Formatted capacity Default logical geometryDrive Guaranteed Mbytes Bytes per Model LBA ModeDrive Model Read/Write heads MR Number of discs Supported CHS translation geometriesPhysical organization Recording and interface technologyST317242A, ST313032A Physical characteristicsDrive Specification ST310232A, ST38422A ST34312A Seek timeRead Write Seek type Msec, typ Power specificationsPower consumption Start/stop timesTypical current profile Mode Typical Watts RMS Typical Amps RMS 12VVoltage tolerance Power-management modesMode Heads Spindle Buffer Conducted noiseHumidity 3.1 Relative Humidity Environmental tolerances Ambient temperatureTemperature gradient 3.2 Wet bulb temperatureNonoperating shock AltitudeShock Operating shockElectromagnetic susceptibility Typical sound Maximum sound Mode Power belsNonoperating vibration Drive acousticsAustralian C-Tick Agency certification Safety certificationReliability Electromagnetic CompatibilityFCC verification Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Jumper settings Master/slave configuration Handling and static-discharge precautionsUltra ATA/66 cable Alternate capacity jumperDrive mounting Alternate capacity and master/slave jumper settingsMounting dimensions-top, side and end view Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a ATA interface ATA interface signals and connector pinsO pins and supported ATA signals Code ATA Interface commands Supported ATA commandsCommand name Supported by ATA-standard commandsATA-standard power-management commands Word Description Value Identify Drive commandWord Description 60-61 Total number of user-addressable Description if bit is set to Bit Word 0CH Set Features commandVendor-specific Yes 4 S.M.A.R.T. commandsA.R.T. Enable/Disable Attribute Yes Autosave A.R.T. Read Data YesD3H Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a Medalist 17242, 13032, 10232, 8422 and 4312, Rev. a
Top Page Image Contents