Seagate ST9300505SS Environmental limits, 300GB models in 6Gb operation, Temperature a. Operating

Page 46

300GB models in 6Gb operation

Typical power dissipation under idle conditions in 6Gb operation is 3.48 watts (11.88 BTUs per hour).

To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3.4123.

Figure 12. 300GB (at 6Gb) DC current and power vs. input/output operations per second

7.5Environmental limits

Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C). Maximum wet bulb temperature is 82°F (28°C).

Note. To maintain optimal performance drives should be run at nominal case temperatures.

7.5.1Temperature a. Operating

The drive meets the operating specifications over a 41°F to 131°F (5°C to 55°C) drive case temperature range with a maximum temperature gradient of 36°F (20°C) per hour.

The maximum allowable drive case temperature is 60°C.

The MTBF specification for the drive assumes the operating environment is designed to maintain nominal case temperature. The rated MTBF is based upon a sustained case temperature of 122°F (50°C). Occa- sional excursions in operating temperature between the rated MTBF temperature and the maximum drive operating case temperature may occur without impact to the rated MTBF temperature. However continual or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the drive MTBF and reduce product reliability.

Air flow may be required to achieve consistent nominal case temperature values (see Section 9.2). To con- firm that the required cooling is provided for the electronics and HDA, place the drive in its final mechanical configuration, and perform random write/read operations. After the temperatures stabilize, measure the case temperature of the drive. See Figure 13 for HDA temperature checkpoint.

38

Savvio 10K.5 SAS Product Manual, Rev. D

Image 46
Contents Standard Models Self-Encrypting Drive Models ST9900605SS ST9600005SS ST9450205SS ST9300405SSSED Fips 140-2 Models Revision history Revision Date Sheets affected or commentsContents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPage Savvio 10K.5 SAS Product Manual, Rev. D List of Figures Page Seagate Technology support services Seagate Online Support and ServicesScope Standard models Standard SED models SED Fips 140-2 modelsElectromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents China Restriction of Hazardous Substances RoHS DirectiveGeneral description Media description Standard featuresPerformance Formatted capacities Factory-installed optionsReliability Programmable drive capacitySeek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesStorage Product warrantyShipping Product repair and return informationPowerChoice modes Physical/electrical specificationsPowerChoiceTM power management Mode DescriptionAC power requirements DC power requirements900GB standard drive DC power requirements 0Gb mode Amps600GB standard drive DC power requirements 450GB standard model DC power requirements 300GB standard model DC power requirements Power sequencing General DC power requirement notesConducted noise immunity Current profiles Current profiles for 900GB modelsCurrent profiles for 600GB models Current profiles for 450GB models Current profiles for 300GB models Power dissipation GB models in 3Gb operation900GB models in 6Gb operation GB models in 3Gb operation 600GB models in 6Gb operation 450GB models in 3Gb operation 450GB models in 6Gb operation 300GB models in 3Gb operation Environmental limits Temperature a. Operating300GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Shock Recommended mountingVibration a. Operating-normal Air cleanlinessCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsPurpose About FipsLevel 2 security About self-encrypting drives Controlled accessAdmin SP Data encryptionData bands Random number generator RNGDrive locking Cryptographic eraseSupported commands Authenticated firmware downloadPower requirements RevertSPDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Background Media ScanDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Levels of PI Setting and determining the current Type LevelProtection Information PI Identifying a Protection Information driveInstallation Physical interfaceDrive orientation CoolingDrive mounting GroundingSAS features Interface requirementsCommand name Command code Supported Scsi commands supportedSupported commands Dual port supportSupported commands Supported commands Supported commands Savvio inquiry data Inquiry dataBytes Data hex Mode Sense data Mode Sense data for 900GB drives Mode PagesMode Sense data for 600GB drives Mode Sense values for 450GB drives Mode Sense values for 300GB drives Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification complianceLED drive signal General interface characteristicsIndex NumericsPage Msid Mtbf See also cooling Page Savvio 10K.5 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST9600005SS, ST9600205SS, ST9300505SS, ST9300605SS, ST9300405SS specifications

Seagate has long been a prominent player in the storage solutions market, offering a range of hard drives that cater to various needs and applications. Among its extensive lineup, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS stand out due to their unique features and robust performance, making them suitable for both personal and professional use.

The Seagate ST9600105SS is a 2.5-inch 600GB SAS hard drive that delivers exceptional reliability and performance. With a rotational speed of 10,000 RPM, this drive ensures quick data access through its enhanced data transfer rate. It utilizes a SAS 6Gb/s interface, allowing for fast and efficient data management in enterprise environments. The drive is designed with Seagate's AgileArray technology, which optimizes drive reliability for multi-drive environments, ensuring that users benefit from reduced downtime.

Similarly, the ST9450405SS and ST9450305SS are also 2.5-inch SAS drives, offering capacities of 450GB and 300GB, respectively. Both models feature a 10,000 RPM speed and a 6Gb/s SAS interface, making them ideal for use in data centers and business-critical applications. The ST9450405SS has enhanced power efficiency, aiding in lowering operational costs for enterprises. Both drives incorporate Seagate's advanced error recovery controls, which help maintain data integrity under varying workloads.

On the larger capacity side, the Seagate ST9900605SS and ST9900805SS drives provide even more storage options. Offering 600GB and 800GB capacities, respectively, these drives are designed for high-performance computing environments. They also spin at 10,000 RPM and support the 6Gb/s SAS interface. The ST9900805SS, in particular, is noted for its advanced performance in transactional workloads, making it suitable for database storage, virtualization, and analytics.

All five models feature Seagate’s innovative technologies, including firmware enhancements for improved error correction and reliability. They are also built to operate in a variety of environments, offering robust vibration tolerance.

In summary, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS represent some of the best storage solutions for high-demand applications. With their emphasis on performance, reliability, and energy efficiency, these drives are engineered to meet the challenges of modern data storage needs, ensuring organizations can rely on them for their critical operations.