Seagate ST9450405SS Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 79

12.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 22. The receiver is AC cou- pling to eliminate ground shift noise.

 

TX

Transmitter

Differential

Transfer Medium

100

 

 

TY

Figure 22. SAS transmitters and receivers

.01

.01

RX

Receiver 100

RY

12.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

12.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 17 for signal type and signal name information.

12.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 18.

Table 18: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

 

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

Format in progress, each cylinder change

 

Toggles on/off

 

 

 

 

Savvio 10K.5 SAS Product Manual, Rev. D

71

Page 78 Page 80
Image 79
Page 78 Page 80
Contents Standard Models Self-Encrypting Drive Models ST9900605SS ST9600005SS ST9450205SS ST9300405SSSED Fips 140-2 Models Revision Date Sheets affected or comments Revision historyContents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPage Savvio 10K.5 SAS Product Manual, Rev. D List of Figures Page Seagate Online Support and Services Seagate Technology support servicesStandard models Standard SED models SED Fips 140-2 models ScopeElectromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive Reference documentsGeneral description Media description Standard featuresPerformance Programmable drive capacity Factory-installed optionsReliability Formatted capacitiesAccess time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Product warrantyShipping StorageMode Description Physical/electrical specificationsPowerChoiceTM power management PowerChoice modesDC power requirements AC power requirements0Gb mode Amps 900GB standard drive DC power requirements600GB standard drive DC power requirements 450GB standard model DC power requirements 300GB standard model DC power requirements Power sequencing General DC power requirement notesConducted noise immunity Current profiles for 900GB models Current profilesCurrent profiles for 600GB models Current profiles for 450GB models Current profiles for 300GB models GB models in 3Gb operation Power dissipation900GB models in 6Gb operation GB models in 3Gb operation 600GB models in 6Gb operation 450GB models in 3Gb operation 450GB models in 6Gb operation 300GB models in 3Gb operation Environmental limits Temperature a. Operating300GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Recommended mounting ShockVibration a. Operating-normal Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesCryptographic erase Random number generator RNGDrive locking Data bandsRevertSP Authenticated firmware downloadPower requirements Supported commandsDrive internal defects/errors Defect and error managementDrive error recovery procedures Background Media Scan SAS system errorsDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Identifying a Protection Information drive Setting and determining the current Type LevelProtection Information PI Levels of PIPhysical interface InstallationCooling Drive orientationGrounding Drive mountingInterface requirements SAS featuresDual port support Scsi commands supportedSupported commands Command name Command code SupportedSupported commands Supported commands Supported commands Savvio inquiry data Inquiry dataBytes Data hex Mode Sense data Mode Pages Mode Sense data for 900GB drivesMode Sense data for 600GB drives Mode Sense values for 450GB drives Mode Sense values for 300GB drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification complianceLED drive signal Differential signalsNumerics IndexPage Msid Mtbf See also cooling Page Savvio 10K.5 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST9600005SS, ST9600205SS, ST9300505SS, ST9300605SS, ST9300405SS specifications

Seagate has long been a prominent player in the storage solutions market, offering a range of hard drives that cater to various needs and applications. Among its extensive lineup, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS stand out due to their unique features and robust performance, making them suitable for both personal and professional use.

The Seagate ST9600105SS is a 2.5-inch 600GB SAS hard drive that delivers exceptional reliability and performance. With a rotational speed of 10,000 RPM, this drive ensures quick data access through its enhanced data transfer rate. It utilizes a SAS 6Gb/s interface, allowing for fast and efficient data management in enterprise environments. The drive is designed with Seagate's AgileArray technology, which optimizes drive reliability for multi-drive environments, ensuring that users benefit from reduced downtime.

Similarly, the ST9450405SS and ST9450305SS are also 2.5-inch SAS drives, offering capacities of 450GB and 300GB, respectively. Both models feature a 10,000 RPM speed and a 6Gb/s SAS interface, making them ideal for use in data centers and business-critical applications. The ST9450405SS has enhanced power efficiency, aiding in lowering operational costs for enterprises. Both drives incorporate Seagate's advanced error recovery controls, which help maintain data integrity under varying workloads.

On the larger capacity side, the Seagate ST9900605SS and ST9900805SS drives provide even more storage options. Offering 600GB and 800GB capacities, respectively, these drives are designed for high-performance computing environments. They also spin at 10,000 RPM and support the 6Gb/s SAS interface. The ST9900805SS, in particular, is noted for its advanced performance in transactional workloads, making it suitable for database storage, virtualization, and analytics.

All five models feature Seagate’s innovative technologies, including firmware enhancements for improved error correction and reliability. They are also built to operate in a variety of environments, offering robust vibration tolerance.

In summary, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS represent some of the best storage solutions for high-demand applications. With their emphasis on performance, reliability, and energy efficiency, these drives are engineered to meet the challenges of modern data storage needs, ensuring organizations can rely on them for their critical operations.
Top Page Image Contents