Seagate ST9900805SS manual Vibration a. Operating-normal, Air cleanliness, Corrosive environment

Page 49

7.5.4.2Vibration a. Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding

5-500 Hz @ 0.5 G (zero to peak)

 

Vibration may be applied in the X, Y, or Z axis.

 

Operating normal translational random flat profile

 

10 - 500 Hz (translational random flat profile)

0.5 GRMS

b.Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:

15 minutes of duration at major resonant frequency 5-500 Hz @ 0.75 G (X, Y, or Z axis)

Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

 

10 - 500 Hz (translational random flat profile)

1.2 GRMS

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding

5-500 Hz @ 3.0 G (zero to peak)

Vibration may be applied in the X, Y, or Z axis.

 

Non-operating translational random flat profile

 

10 - 500 Hz (translational random flat profile)

2.4 GRMS

7.5.5Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

7.5.6Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Savvio 10K.5 SAS Product Manual, Rev. D

41

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Standard Models Self-Encrypting Drive Models ST9900605SS ST9600005SS ST9450205SS ST9300405SSSED Fips 140-2 Models Revision Date Sheets affected or comments Revision historyContents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPage Savvio 10K.5 SAS Product Manual, Rev. D List of Figures Page Seagate Online Support and Services Seagate Technology support servicesStandard models Standard SED models SED Fips 140-2 models ScopeStandards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCChina Restriction of Hazardous Substances RoHS Directive Reference documentsGeneral description Media description Standard featuresPerformance Reliability Factory-installed optionsFormatted capacities Programmable drive capacityInternal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyStorage Product repair and return informationPowerChoiceTM power management Physical/electrical specificationsPowerChoice modes Mode DescriptionDC power requirements AC power requirements0Gb mode Amps 900GB standard drive DC power requirements600GB standard drive DC power requirements 450GB standard model DC power requirements 300GB standard model DC power requirements Power sequencing General DC power requirement notesConducted noise immunity Current profiles for 900GB models Current profilesCurrent profiles for 600GB models Current profiles for 450GB models Current profiles for 300GB models GB models in 3Gb operation Power dissipation900GB models in 6Gb operation GB models in 3Gb operation 600GB models in 6Gb operation 450GB models in 3Gb operation 450GB models in 6Gb operation 300GB models in 3Gb operation Environmental limits Temperature a. Operating300GB models in 6Gb operation Effective altitude sea level a. Operating Relative humidityShock and vibration Recommended mounting ShockVibration a. Operating-normal Air cleanlinessCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Admin SP Controlled accessAbout self-encrypting drives Data encryptionDrive locking Random number generator RNGData bands Cryptographic erasePower requirements Authenticated firmware downloadSupported commands RevertSPDrive internal defects/errors Defect and error managementDrive error recovery procedures Background Media Scan SAS system errorsDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Protection Information PI Setting and determining the current Type LevelLevels of PI Identifying a Protection Information drivePhysical interface InstallationCooling Drive orientationGrounding Drive mountingInterface requirements SAS featuresSupported commands Scsi commands supportedCommand name Command code Supported Dual port supportSupported commands Supported commands Supported commands Savvio inquiry data Inquiry dataBytes Data hex Mode Sense data Mode Pages Mode Sense data for 900GB drivesMode Sense data for 600GB drives Mode Sense values for 450GB drives Mode Sense values for 300GB drives Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification complianceDifferential signals General interface characteristicsNumerics IndexPage Msid Mtbf See also cooling Page Savvio 10K.5 SAS Product Manual, Rev. D Page Seagate Technology LLC

ST9600005SS, ST9600205SS, ST9300505SS, ST9300605SS, ST9300405SS specifications

Seagate has long been a prominent player in the storage solutions market, offering a range of hard drives that cater to various needs and applications. Among its extensive lineup, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS stand out due to their unique features and robust performance, making them suitable for both personal and professional use.

The Seagate ST9600105SS is a 2.5-inch 600GB SAS hard drive that delivers exceptional reliability and performance. With a rotational speed of 10,000 RPM, this drive ensures quick data access through its enhanced data transfer rate. It utilizes a SAS 6Gb/s interface, allowing for fast and efficient data management in enterprise environments. The drive is designed with Seagate's AgileArray technology, which optimizes drive reliability for multi-drive environments, ensuring that users benefit from reduced downtime.

Similarly, the ST9450405SS and ST9450305SS are also 2.5-inch SAS drives, offering capacities of 450GB and 300GB, respectively. Both models feature a 10,000 RPM speed and a 6Gb/s SAS interface, making them ideal for use in data centers and business-critical applications. The ST9450405SS has enhanced power efficiency, aiding in lowering operational costs for enterprises. Both drives incorporate Seagate's advanced error recovery controls, which help maintain data integrity under varying workloads.

On the larger capacity side, the Seagate ST9900605SS and ST9900805SS drives provide even more storage options. Offering 600GB and 800GB capacities, respectively, these drives are designed for high-performance computing environments. They also spin at 10,000 RPM and support the 6Gb/s SAS interface. The ST9900805SS, in particular, is noted for its advanced performance in transactional workloads, making it suitable for database storage, virtualization, and analytics.

All five models feature Seagate’s innovative technologies, including firmware enhancements for improved error correction and reliability. They are also built to operate in a variety of environments, offering robust vibration tolerance.

In summary, the Seagate ST9600105SS, ST9450405SS, ST9450305SS, ST9900605SS, and ST9900805SS represent some of the best storage solutions for high-demand applications. With their emphasis on performance, reliability, and energy efficiency, these drives are engineered to meet the challenges of modern data storage needs, ensuring organizations can rely on them for their critical operations.
Top Page Image Contents