Seagate ST980825A, ST96023A, ST94015A manual Reliability, Agency certification, Safety certification

Page 20

2.13

Reliability

 

 

 

Measurement type

Specification

 

 

Nonrecoverable read errors

1 per 1014 bits read, max

Annualized Failure Rate (AFR)

0.73%

 

 

Load/Unload (U/UL)

 

40°C, 50% relative humidity

600,000 software-controlled power on/off cycles

 

 

20,000 hard power on/off cycles

32°C, 80% relative humidity

100,000 software-controlled power on/off cycles

5°C, 80% relative humidity

20,000 hard power on/off cycles

5°C, 10% relative humidity

 

55°C, 16% relative humidity

 

 

 

Service Life

5 Years

 

 

 

Warranty

 

5 Years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to access the

 

 

following web page:

 

 

www.seagate.com/support/service/

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

 

 

vide the drive serial number, model number (or part number) and country of pur-

 

 

chase. The system will display the warranty information for your drive.

 

 

 

2.14Agency certification

2.14.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.

2.14.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

14

Momentus 7200.1 PATA Product Manual, Rev. C

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Momentus 7200.1 Pata ST910021A ST980825A ST96023A ST94015APage Contents Momentus 7200.1 Pata Product Manual, Rev. C List of Figures Momentus 7200.1 Pata Product Manual, Rev. C Introduction Momentus 7200.1 Pata disc driveMomentus 7200.1 Pata Product Manual, Rev. C Drive specifications Specification summarySpecifications Drive specification ST910021A ST980825A ST96023A ST94015A+5V ± 5% / -8% startup Default logical geometry LBA modeFormatted capacity Physical organizationRecording and interface technology Physical characteristicsTechnology Specification Seek time Time to readyTypical seek times msec Read Write Time to ready Typical MaxPower specifications Voltage tolerance Typical current profileConducted noise Power-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunitySafety certification Measurement type SpecificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 Environmental protection European Union Restriction of Hazardous Substances RoHS表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国 Momentus 7200.1 Pata Product Manual, Rev. C Configuring and mounting the drive Handling and static discharge precautionsJumper settings Master/slave configurationDrive mounting Cable-select optionATA interface signals and connector pins Connector signalsConnector Cable Signal Name Contact Conductor Cable Connector Conductor Contact Signal NameCommand name Command code in hex ATA-standard commands Supported ATA commandsSupported commands ATA-standard security commands Command name Command code in hexATA-standard power-management commands Supported commands Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordSet Features command Features register valuesSeagate Technology support services InternetPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page Page Momentus 7200.1 Pata Product Manual, Rev. C Page Seagate Technology LLC
Top Page Image Contents